SUNFLY A6 Wireless Headset User Manual

SUNFLY A6 Wireless Headset

Product Specifications

• Device Type: Wireless Headset
• FCC Compliance: Part 15 of the FCC Rules
• RF Exposure: Meets general RF exposure requirements, suitable for portable use without restriction.

FCC Compliance and Interference

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

If you experience interference, please ensure the device is not in proximity to other electronic devices that may be emitting strong signals.

Thank you for choosing our headphones. The A6 is a pair of OWS business headphones, featuring a V6.0 chip design. It has dual-microphone noise cancellation to enhance call quality. The product design is novel and comfortable to wear. Paired with a large-capacity charging case, it offers an integrated charging and storage solution, significantly improving the product’s battery life.

Package Content

Parameters

• BT version: V6.0
• Working range: 10M
• Headphone battery capacity: 100mAh
• Battery capacity of the charging case: 950mAh
• Headphone charging time: 1.5h
• Charging time of the charging dock: 2h
• working hours: 8h

Overview

Charging Instructions

Before using your headphones for the first time or if you haven’t used them for more than one month, please make sure to place the headphones in the charging case and connect the Type-C cable for charging until the charging indicator on the case shows 100%, indicating a full charge. Under normal circumstances, the fully charged state of the charging case can provide approximately 6 complete charging cycles for the headphones.

Wear headphones

Insert the earbuds into your right ear as shown in the illustration below, then gently rotate them to a comfortable position.

Power on

• Earbuds in the charging case: Remove the earbuds, and they will automatically power on with the indicator light illuminating.
• Earbuds outside the charging case: While powered off, press and hold the “Power On/Off” button for approximately 3 seconds to power on the earbuds, with the indicator light illuminating.

Power off

• Earbuds outside the charging case: Press and hold the earbuds’ “Power On/Off” button for about 3 seconds until the earbuds power off. The orange light will flash rapidly for 3 seconds before turning off.
• Earbuds placed in the charging case: Place the earbuds inside the case. The earbuds will automatically power off and enter charging mode.

Pairing Connection

• First Use: After turning on the headphones, they automatically enter pairing mode with alternating orange and white light flashes. Open your phone’s Bluetooth settings to search for new devices, select “A6,” and tap Connect. Once your phone displays “Bluetooth device connected” or the pairing light on the headphones turns off, the headphones are successfully connected to your phone.
• Subsequent Use: After turning on the headphones, they will automatically reconnect to your phone.

Music Playback Controls

• Play/Pause: While music is playing, briefly press the headset’s “Power” button to play or pause music.
• Previous Track: While music is playing, press and hold the headset’s “Volume Up” button to play the previous track.
• Next Track: While music is playing, press and hold the headset’s “Volume Down” button to play the next track.

Volume Control

• Increase Volume: During a call or while playing music, briefly press the “Volume Up” button on the headset to increase the volume.
• Decrease Volume: During a call or while playing music, briefly press the “Volume Down” button on the headset to decrease the volume.

Call Control

• Answer/End Call: When the headphone rings, short-press the “Power On/Off” button to answer the call.
• During a call, short-press the “Power On/Off” button to end the call.
• Reject Call: When the headphone rings, press and hold the “Power On/Off” button to reject the incoming call.

Microphone Mute

• Mute Microphone: During a call, press and hold the “Microphone Mute” button to disable microphone output.
• Unmute Microphone: During a call, press and hold the “Microphone Mute” button to restore microphone output.

Language Switch

While in pairing mode, double-click the “Power On/Off” button to switch languages.

Clear Information and Force Pairing

• Clear Pairing Information: With the earbuds in the charging case, quickly press the “Clear/Pair” button 5 times to erase all paired devices from the earbuds.
• Force Pairing: With the earbuds in the charging case, quickly press the “Clear/Pair” button twice to force the earbuds into pairing mode.

Warranty Feedback Form

Frequently Asked Questions

Is this device safe to use close to my body?
Yes, the device has been evaluated to meet general RF exposure requirements and can be used in portable exposure conditions without restriction.

What should I do if my headset is not working?
Please refer to the troubleshooting section for common issues. If the problem persists, contact customer support.