Linklemo A9 Smart Mini Camera App User Manual

Linklemo A9 Smart Mini Camera App User Manual

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interferenc
(2)this device must accept any interference received, including interference that may cause unde operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This device meets the FCC requirements for RF exposure.The device is designed for normal indoor use and complieswith applicable FCC exposure limits.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body

Smart camera

Instruction Manual

Download and Install the APP

Using WeChat/browser, etc., scan the QR code to download and install the APP;

Download and Install the APP

APP Connection

(1) Open the APP, register and log in;
(2) Open the mobile phone settings to connect to 2.4G WiFi(wireless fidelity) and turn on the mobile phone Bluetooth;
(3) Enter the distribution network mode
a. Button Model: Long press ON / OFF for 2 seconds to open the machine, long press MODE for 6 seconds until the blue indicator light flashes to enter the distribution network mode;
Net connection: Click “Add Device” in APP to automatically scan devices until the device
” is scanned (FIG. 1), click “Bind Now” corresponding device and click “Next” (FIG. 2). After adding the successful blue indicator lights on, you can customize the device name (FIG. 3), which means successful addition.

Figure 1-3

* If the device cannot be added for a long time, long press the MODE key for 6 seconds to re-enter the distribution network mode

No network connection: open the wifi setting in the mobile phone setting, select the name at the beginning of LLM _ click enter password: 12345678 and connect, open the APP after the connection, click the pop-up “Cancel” (Figure 4) to complete the connection, click to view the live video (ensure to select the allowed location authorization when entering the APP).

Figure 4

Matters Needing Attention

No network connection:

  1. Unable to remotely monitor video footage.
    Every time you need to watch, your phone is about 10 meters closer to the camera (open and unobstructed)
  2. Connect to LLM _ in the Wifi and then open the APP to watch
  3. During the connection of the camera’s WiFi, it is normal to not be able to access the internet normally. Disconnect the WiFi and it can be restored

Net connection:

  1. The camera distance from the router Wifi shall not exceed 5 meters;
  2. Wifi with a 5G name cannot be used;
  3. Try not to be close to the metal door installation (it will affect the Wifi signal to shorten the connection distance);
  4. Ensure that the camera is connected to the charging power supply;
  5. When the installation is completed, please remove the lens protective film before use.

Documents / Resources

PDF thumbnailA9 Smart Mini Camera App
User Manual · X6D, 2BGNZ-X6D, 2BGNZX6D, A9 Smart Mini Camera App, A9, Smart Mini Camera App, Mini Camera App, Camera App

References

Questions and answers

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Browse all questions about this manual

Questions & Answers

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

  1. I would like to know how long the battery lasts on these mini cameras when the motion detector is enabled. Thank you.

    🇧🇷 Tiao Silva asks I would like to know how long the battery lasts on these mini cameras when the motion detector is enabled. Thank you.
    Manuals+ clarified question
    Question

    How long does the battery last on the Linklemo A9 Smart Mini Camera when motion detection is enabled?

    Answer

    The provided manual for the Linklemo A9 Smart Mini Camera does not specify exact battery life durations or mAh capacity. Generally, for mini cameras of this type, battery life varies significantly based on the frequency of motion triggers and the quality of the Wi-Fi connection.

    However, the manual notes in the "Matters Needing Attention" section that you should ensure the camera is connected to a charging power supply for continuous operation. If you are using the camera on its internal battery with motion detection enabled, you can typically expect a few hours of active recording time, though it may last longer in standby mode if triggers are infrequent. For reliable long-term monitoring, it is recommended to keep the device plugged into a USB power source.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.