1. Bubuka
The SUNLU Filament Dryer SP2 is designed to dry 3D printer filaments and provide sealed storage, improving print quality by removing moisture. This device features a heating element, an HD LCD touch screen for control, and compatibility with various filament types and spool sizes.
Image 1.1: SUNLU Filament Dryer SP2, highlighting its purpose.
2. Émbaran Kasalametan
- Pastikeun catu dayana cocog sareng sarat alat.
- Do not touch the heating element or interior surfaces during operation, as they can become hot.
- Jauhkeun alat tina cai atawa cairan séjén.
- Entong meungpeung lawang angin.
- Cabut colokan alat sateuacan beberesih atanapi perawatan.
- Jauhkeun tina jangkauan barudak.
3. Eusi Paket
Pastikeun yén sadaya item aya dina bungkusan:
Image 3.1: Detailed packing list for the SP2 FilaDryer Set.
- Drying Chamber x1
- Heating Base x1
- Air Lock x2
- Kabel Daya x1
- Spool Roller x1
- Rollers & Bearings x1
- Buku Panduan x1
- Desiccant Box x1
- Desiccant x1
- Hygrometer x1
- PTFE Tube 1m x2
- PTFE Tube 8cm x2
4. Produk Langkungview
The SUNLU Filament Dryer SP2 consists of a detachable drying chamber and a heating base, allowing for both drying and sealed storage. Key components include:
- Panutup Top: Seals the drying chamber.
- Kamar Pangeringan: Transparent enclosure for filament spools.
- Hygrometer: Displays real-time interior humidity.
- Dasar pemanasan: Contains the PTC heating element and control panel.
- Spool Rollers: Support filament spools for smooth rotation.
- PTFE Tubes: Guide filament to the 3D printer.
Gambar 4.1: Ngabeledug view of the SP2 components.
5. Parentah Setup
- Ngabongkar: Sacara saksama miceun sadaya komponén tina bungkusan.
- Assemble Rollers: Place the spool rollers and bearings into the designated slots within the drying chamber.
- Insert Desiccant: Place the desiccant into the desiccant box and insert it into its compartment in the drying chamber.
- Sambungkeun Kakuatan: Plug the power cable into the heating base and then into a suitable power outlet.
- Load Filament: Open the top cover and place your filament spool(s) onto the rollers inside the drying chamber. The unit can accommodate up to two 1kg spools or one 3kg spool.
- Route Filament (for printing): If you intend to print while drying, route the filament through one of the PTFE tubes and out through an air lock to your 3D printer.
- Tutup panutup: Securely close the top cover using the two sliding latches to ensure a tight seal.
Image 5.1: Fully assembled SUNLU Filament Dryer SP2 with filament spools.
6. Parentah Operasi
6.1 Daya Hurung/Pareuman
Press the power button on the HD LCD touch screen to turn the device on or off.
6.2 Using the HD LCD Touch Screen
The touch screen allows you to monitor and adjust drying parameters. It displays current temperature (PV), target temperature (SV), selected filament type, and remaining drying time.
Image 6.1: HD LCD Touch Screen interface.
6.3 Nyetel Suhu jeung Waktu
- Select Filament Type: Tap the filament type icon to cycle through presets (PLA, PETG, TPU, ABS, PA, PC, WOOD, PVA, PVB, ASA). Each preset has recommended temperature and time settings.
- Saluyukeun Suhu: Tap the temperature display (SV) and use the up/down arrows to set the desired drying temperature (range: 35-70°C).
- Saluyukeun waktos: Tap the time display and use the up/down arrows to set the desired drying duration (range: 0-99 hours).
- The device will begin heating to the set temperature and maintain it for the specified duration.
Image 6.2: Recommended Filament Drying Temperatures and Times.
6.4 Monitoring Humidity
The integrated hygrometer displays the current humidity level inside the drying chamber, allowing you to monitor the drying process. For optimal results, aim for a low humidity percentage.
6.5 Drying and Storage Functionality
The SP2 can be used for active drying or passive sealed storage. The detachable design allows the drying chamber to be lifted from the heating base for convenient storage after drying. The superior sealing mechanism, including silicone holes and sliding latches, helps maintain low humidity for stored filaments.
Image 6.3: Drying and Storage capabilities with various spool sizes.
7. Pangropéa
- beberesih: Wipe the exterior with a soft, dry cloth. Do not use abrasive cleaners or immerse the device in water. Ensure the device is unplugged and cool before cleaning.
- Desiccant: Periodically check the desiccant. If it changes color (indicating saturation), it needs to be recharged or replaced. Follow the desiccant manufacturer's instructions for recharging.
- PTFE Tubes: Inspect PTFE tubes for wear or blockages. Replace if necessary to ensure smooth filament feeding.
8. Cara ngungkulan
| Masalah | Mungkin Cukang lantaranana | Solusi |
|---|---|---|
| Filament still exhibits moisture-related print issues (stringing, poor adhesion). | Insufficient drying time or temperature; saturated desiccant; poor seal. | Increase drying time or temperature; replace/recharge desiccant; ensure top cover is securely latched. |
| Device not heating. | Power cable not connected; device not powered on; internal fault. | Check power connections; press power button; contact support if problem persists. |
| LCD touch screen unresponsive. | Gangguan parangkat lunak samentawis; masalah daya. | Power cycle the device (turn off, unplug, wait 30 seconds, plug in, turn on). |
| Filament spool not rotating smoothly. | Rollers obstructed or dirty; filament tangled. | Clean rollers; untangle filament; ensure PTFE tubes are clear. |
Image 8.1: Visual comparison of print quality with moist vs. dry filament.
9. Spésifikasi
- model: SUNLU Filament Dryer SP2
- Unsur pemanasan: 250W PTC
- Suhu maksimum: 70°C
- Kasaluyuan filamén: 1.75mm, 2.85mm (PLA, PETG, TPU, ABS, PA, PC, WOOD, PVA, PVB, ASA)
- Kapasitas Spool: Up to 2 x 1kg spools or 1 x 3kg spool. Supports 250g, 500g spools.
- Ukuran produk (L x W x H): 278mm x 208mm x 396mm (kira-kira 10.9 x 8.2 x 15.6 inci)
- Beurat barang: 3.6 kg (7.92 pon)
- Kontrol: HD LCD Touch Screen
- Pangimeutan kalembaban: Integrated Hygrometer
Image 9.1: Product dimensions of the SUNLU Filament Dryer SP2.
10. Garansi jeung Rojongan
For warranty information and technical support, please refer to the warranty card included with your product or visit the official SUNLU website. You may also contact SUNLU customer service directly for assistance with product operation, troubleshooting, or parts replacement.
