1. Bubuka
This manual provides comprehensive instructions for the installation, operation, and maintenance of your SINOTIMER PID Temperature Controller Kit. This kit is designed for precise temperature regulation in various industrial and domestic applications, offering stable and accurate control. Please read this manual thoroughly before installation and operation to ensure safe and efficient use.
2. Produk Langkungview
The SINOTIMER PID Temperature Controller Kit includes the following components:
- PID Temperature Controller: An intelligent digital controller for accurate temperature management.
- SSR 40DA Solid State Relay: A high-current solid-state relay for switching heating elements.
- K-Type Screw Thermocouple: A temperature sensor for measuring the process variable.
- Panyerep panas: For dissipating heat from the Solid State Relay, ensuring stable operation.
Fitur konci:
- Supports K, E, J type thermocouple inputs.
- Equipped with both SSR and Relay control outputs.
- Includes one alarm relay output (AC220V/DC30V 3A NO/NC).
- Digital display with selectable Celsius (℃) or Fahrenheit (℉) units.
- Compact design with standard 45x45mm hole size for easy installation.
Figure 2.1: Complete SINOTIMER PID Temperature Controller Kit, showing the PID controller, SSR 40DA, K-Type Thermocouple, and heat sink.
3. Spésifikasi
| Parameter | Nilai |
|---|---|
| Modél | 40DA |
| Sasayogian tanaga | AC 100-240V, 50/60Hz |
| Tipe Input | K, E, J Thermocouple |
| Rentang Suhu | 0-999 ℃ / ℉ |
| Tipe Kaluaran | Relay / SSR |
| Kaluaran Alarm | AC220V/DC30V 3A (Resistive load) NO/NC |
| Kaluaran SSR | 40DA (Included) |
| Ukuran Panel | 48 mm x 48 mm |
| Ukuran liang | 45 mm x 45 mm |
| Item Beurat | 12.6 ons |
4. Setup jeung Instalasi
4.1 Instalasi fisik
The PID controller is designed for panel mounting. Ensure the mounting hole dimensions are 45mm x 45mm. The heat sink should be securely attached to the SSR 40DA to prevent overheating.
Figure 4.1: Dimensions of the SINOTIMER PID Temperature Controller (48mm x 48mm front panel, 75mm depth).
Figure 4.2: Dimensions of the heat sink (80x50x50mm) and the M6 K-type screw thermocouple (2m cable length).
4.2 Diagram Wiring
WARNING: Ensure all power is disconnected before performing any wiring. Incorrect wiring can lead to equipment damage or personal injury. If you are unsure, consult a qualified electrician.
Refer to the wiring diagrams below for proper connection of the PID controller, SSR, and thermocouple. The controller requires AC 100-240V power supply.
Figure 4.3: Back panel of the PID controller showing terminal assignments for power (1, 2), SSR output (3, 4), alarm output (5, 6), and thermocouple input (11, 12).
Gambar 4.4: Kelample physical wiring diagram for connecting the SSR 40DA to the PID controller and a heating element. Terminals 1 and 2 on the SSR connect to the AC load (heater), and terminals 3 and 4 connect to the DC control output (3-32VDC) from the PID controller.
Catetan Kabel:
- Connect the K-Type Thermocouple to terminals 11 and 12. Ensure correct polarity (positive to 12, negative to 11).
- Connect the main AC power supply (100-240V) to terminals 1 and 2 of the PID controller.
- Connect the SSR control output from the PID controller (terminals 3 and 4) to the input terminals (3-32VDC) of the SSR 40DA.
- Connect the AC load (e.g., heater) to the output terminals (24-380VAC) of the SSR 40DA.
- The alarm output (terminals 5 and 6) can be connected to an external alarm device if required.
5. Parentah Operasi
5.1 Témbongkeun jeung Control Panel
The front panel of the PID controller features a digital display and control buttons:
Figure 5.1: Front panel layout of the SINOTIMER PID Temperature Controller, indicating PV/SV displays, control indicators, and function keys.
- PV (Nilai Proses) Tampilan: Némbongkeun suhu anu diukur ayeuna.
- SV (Atur Nilai) Tampilan: Shows the target temperature or parameter setting value.
- Indikator OUT: Lights up when the control output (to SSR) is ON.
- Indikator AT: Blinks when the self-tuning function is active.
- AL1 Indicator: Lights up when the alarm output is ON.
- konci MODE: Used to enter parameter settings and navigate between modes. Press and hold to store set values.
- Shift Key (<): Used for digit shifting during value adjustment.
- Decrease Key (↓): Used to decrease values.
- Increase Key (↑): Used to increase values.
5.2 Setting the Target Temperature (SV)
- In normal operation mode, the upper display shows PV (current temperature) and the lower display shows SV (target temperature).
- Ngagunakeun éta Increase (↑) jeung Decrease (↓) keys to adjust the SV to your desired temperature.
- Ngagunakeun éta Shift (<) key to move the cursor between digits for faster adjustment.
- The new SV will be automatically saved after a few seconds of inactivity or by pressing the MODÉ konci.
5.3 Setélan Parameter Lanjutan
To access advanced settings (e.g., PID parameters, alarm settings, input type, unit selection), press and hold the MODÉ key for several seconds. Use the MODÉ key to cycle through parameters, and the Shift (<), Increase (↑), jeung Decrease (↓) keys to adjust values. Refer to the detailed parameter list in the full product manual for specific functions and ranges.
6. Pangropéa
Regular maintenance ensures the longevity and optimal performance of your PID temperature controller kit.
- beberesih: Periodically clean the controller's front panel with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Pamariksaan: Regularly check all wiring connections for tightness and signs of wear or damage. Ensure the thermocouple is securely in place and free from corrosion.
- Panyerep panas: Verify that the heat sink on the SSR is free from dust and debris to ensure efficient heat dissipation.
- Lingkungan: Ensure the controller is operated within its specified environmental conditions (temperature, humidity) to prevent malfunction.
7. Cara ngungkulan
If you encounter issues with your PID temperature controller, refer to the following common problems and solutions:
| Masalah | Mungkin Cukang lantaranana | Solusi |
|---|---|---|
| Kontroler teu hurung | Teu aya catu daya; kabelna salah | Check power connections (terminals 1 & 2); ensure power source is active. |
| Layar PV némbongkeun 'HHHH' atawa 'LLLL' | Thermocouple open circuit or reverse connection; temperature exceeds range | Check thermocouple wiring and polarity; ensure it's within operating range. |
| Output (OUT indicator) not activating | SV not set correctly; PID parameters incorrect; SSR faulty | Verify SV is below PV (for heating); check PID settings; test SSR functionality. |
| Temperature unstable or overshoots | PID parameters not optimized | Perform auto-tuning (AT function) or manually adjust PID parameters. |
If the problem persists after attempting these solutions, please contact SINOTIMER customer support for further assistance.
8. Émbaran Kasalametan
- Salawasna pegatkeun daya sateuacan dipasang, dipasang kabel, atanapi diropéa.
- Ensure all wiring is done by a qualified individual and complies with local electrical codes.
- Do not operate the device in environments with excessive moisture, dust, or corrosive gases.
- The SSR generates heat during operation; ensure adequate ventilation and proper heat sink installation.
- This device is not intended for life-support applications or where malfunction could result in significant injury or damage.
9. Garansi jeung Rojongan
For warranty information and technical support, please refer to the product packaging or contact SINOTIMER directly through their official website or the retailer where the product was purchased. Please have your product model number (40DA) and purchase details ready when contacting support.
