LAUNCH Original Adapter for DBSCar VII and SmartLink C VCI Connector User Manual

1. Langkungview

The LAUNCH Original Adapter is a replacement connector designed to facilitate communication between your LAUNCH diagnostic tool and a vehicle's OBD2 port. This adapter converts a DR15 male connection from your DBSCar VII or SmartLink C VCI Device Cable to a standard OBD2 16-pin male connector. It is constructed from zinc-plated copper to ensure reliable and corrosion-resistant connections.

Catetan penting: This product is solely a connector and does not possess any diagnostic functions on its own. It requires a compatible LAUNCH diagnostic device for operation. Please confirm your specific device model before purchase to ensure compatibility.

2. Komponén produk

Pakétna ngawengku barang-barang ieu:

• 1 x DR15 Male to OBD2 16 Pin Male Replacement Adapter

2.1 adaptor Views

Gambar 1: Hareup jeung pungkur views of the LAUNCH adapter, highlighting both connector types.

Gambar 2: Detil view of the 3-Row DR15 Male Connector.

Gambar 3: Detil view of the OBD2 16-Pin Male Connector.

3. Kasaluyuan

This diagnostic adapter is specifically designed for use with DBSCar VII (DBSCar 7) or SmartLink C Device Cables from LAUNCH. It is compatible with a wide range of LAUNCH X431 diagnostic scanners, including but not limited to:

• CRP919XBT
• CRP919EBT
• CRP919MAX
• PRO3 ACE
• PROS V/V+5.0
• PRO3S+ V5.0
• PRO TT Elite
• PRO Dyno
• X431 V+ HD
• PRO 5
• PAD VII
• PAD V

Ensure your diagnostic device utilizes a DBSCar VII or SmartLink C Device Cable for proper connection with this adapter.

4. Setup & Sambungan

Follow these steps to properly connect the adapter for diagnostic use:

1. Connect to VCI Device: Plug the DR15 male end of the adapter into the corresponding DR15 female port on your LAUNCH DBSCar VII or SmartLink C VCI Device Cable. Ensure a secure and firm connection.
2. Nyambung ka Kendaraan: Locate your vehicle's OBD2 diagnostic port (typically found under the dashboard on the driver's side). Plug the OBD2 16-pin male end of the adapter into the vehicle's OBD2 port.
3. Pariksa sambungan: Once both ends are connected, ensure all connections are snug. The adapter is now ready to facilitate communication between your diagnostic tool and the vehicle.

4.1 Diagram Sambungan

Figure 4: Connection diagram for DBSCar VII with the diagnostic adapter.

Figure 5: Connection diagram for SmartLink C with the diagnostic adapter.

5. Parentah Operasi

The LAUNCH Original Adapter serves as a passive connector. Its primary function is to establish a physical link between your LAUNCH diagnostic tool and the vehicle. All diagnostic operations, data reading, and fault code analysis are performed directly through your compatible LAUNCH diagnostic scanner.

Refer to the user manual of your specific LAUNCH diagnostic tool (e.g., X431 CRP919EBT, PRO3 ACE, PAD VII) for detailed instructions on how to perform vehicle diagnostics, access functions, and interpret results.

6. Pangropéa

Pikeun mastikeun umur panjang sareng kinerja optimal adaptor anjeun, turutan pedoman perawatan ieu:

• beberesih: Regularly wipe the adapter's exterior with a soft, dry cloth. Avoid using harsh chemicals or abrasive materials that could damage the zinc-plated copper finish.
• Panyimpenan: Store the adapter in a clean, dry environment away from extreme temperatures, direct sunlight, and moisture. Keep it protected from physical impact to prevent damage to the connectors.
• Pamariksaan: Periodically inspect the connectors for any signs of wear, corrosion, or damage. Ensure the pins are straight and free from debris. The zinc-plated copper construction is designed to resist corrosion and oxidation, but proper care is still recommended.

7. Cara ngungkulan

If you encounter issues while using the adapter, consider the following:

• Henteu aya sambungan: Ensure both the DR15 and OBD2 connections are fully seated and secure. A loose connection can prevent communication.
• Incompatible Device: Verify that your LAUNCH diagnostic tool uses a DBSCar VII or SmartLink C Device Cable. This adapter is not universally compatible with all LAUNCH products.
• Ruksakna Fisik: Inspect the adapter for any visible signs of damage to the cable or connectors. If damaged, replace the adapter.
• Adapter Size Mismatch: Some users have reported issues with the adapter not fitting certain DBScan VII cables, describing it as 'too small'. Always confirm your device model and connector type before purchasing to avoid compatibility problems.

For further assistance, refer to the troubleshooting section of your LAUNCH diagnostic tool's manual or contact LAUNCH customer support.

8. Spésifikasi

9. Jaminan & Dukungan

This LAUNCH Original Adapter comes with a garansi 2 taun ti tanggal pameseran. Garansi ieu nutupan cacad manufaktur sareng mastikeun produk nyumponan standar kualitas.

For any questions, technical assistance, or warranty claims, please feel free to contact LAUNCH customer support. Refer to your product packaging or the official LAUNCH websitus pikeun inpo kontak panganyarna.