Manual Instruksi Perlengkapan LED Banjir Luar Ruangan Philips 196074 SF100-SCT-T-G2

1. Bubuka

Thank you for choosing the Philips 196074 SF100-SCT-T-G2 Outdoor Flood LED Fixture. This manual provides essential information for the safe installation, operation, and maintenance of your new LED floodlight. Please read these instructions thoroughly before installation and retain them for future reference.

This fixture is designed for outdoor use, providing powerful and efficient illumination with selectable lumen output and color temperature options. It features a durable construction and an integrated photocell for automatic operation.

2. Parentah Kasalametan

PERHATOSAN: Pikeun ngurangan résiko maot, tatu pribadi, atawa karuksakan harta tina seuneu, shock listrik, ragrag bagian, motong / abrasions, sarta hazards sejenna, baca sakabeh warnings jeung parentah nu kaasup jeung dina kotak fixture jeung sagala labél fixture.

• Pamasangan kedah dilakukeun ku tukang listrik anu mumpuni saluyu sareng sadaya kode listrik nasional sareng lokal anu berlaku.
• Pegatkeun sambungan kakuatan dina sekering atawa circuit breaker saméméh instalasi atawa ngalayanan.
• Mastikeun suplai voltage is compatible with the fixture's requirements (120 to 347V AC).
• Do not handle energized fixtures with wet hands or when standing on wet or damp surfaces.
• Use only UL-approved wire for connections.
• This fixture is rated IP65 for protection against dust and water jets. Do not submerge.
• Ulah nempo langsung kana operasi sumber lampu LED.

3. Eusi Paket

Pastikeun yén sadaya komponén aya sareng henteu ruksak sateuacan neraskeun pamasangan.

• Philips 196074 SF100-SCT-T-G2 Outdoor Flood LED Fixture (1 unit)
• Yoke/Trunnion Mount (pre-attached or separate)
• Installation Hardware (screws, washers, nuts)
• Manual Pitunjuk (dokumén ieu)

Image 1: Philips 196074 Flood LED Fixture with included mounting hardware. The fixture is a rectangular bronze unit with an integrated LED panel and a U-shaped yoke mount.

4. Setup jeung Instalasi

This fixture is designed for ground, pole, or wall mounting using the provided yoke/trunnion mount.

4.1 Pra-Pasang

1. Pareuman kakuatan: Ensure power to the installation area is disconnected at the circuit breaker or fuse box.
2. Select mounting location: Choose a sturdy surface capable of supporting the fixture's weight. Ensure adequate clearance for light distribution.
3. Nyiapkeun kabel: Run appropriate electrical wiring (120-347V AC) to the chosen mounting location.

4.2 Masangkeun fixture

1. Position the yoke/trunnion mount against the desired surface. Mark the drilling points.
2. Bor liang pilot sakumaha ditandaan.
3. Secure the yoke/trunnion mount to the surface using the provided hardware. Ensure it is firmly attached.
4. Adjust the angle of the fixture as needed and tighten the pivot bolts on the yoke to secure its position.

4.3 Sambungan Listrik

1. Open the wiring compartment on the fixture (if applicable) or access the wiring leads.
2. Connect the fixture's black wire to the supply's live/hot wire.
3. Connect the fixture's white wire to the supply's neutral wire.
4. Connect the fixture's green or bare copper wire to the supply's ground wire.
5. Ensure all connections are secure using UL-approved wire connectors.
6. Close and seal the wiring compartment to maintain the IP65 rating.

5. Parentah Operasi

The Philips 196074 fixture features selectable lumen output and color temperature, along with an integrated photocell for automatic dusk-to-dawn operation.

5.1 Lumen and Color Temperature Selection

Before powering on the fixture, locate the selector switches on the side or back of the unit. These switches allow you to choose the desired lumen output and color temperature.

• Lumen Output Options: 9,540 lm, 12,320 lm, 14,800 lm
• Pilihan Suhu Warna: 3000K (Bodas Haneut), 4000K (Bodas Tiis), 5000K (Daylight)

Set the switches to your preferred combination. Changes made while the fixture is powered may not take effect immediately or may require a power cycle.

5.2 Photocell Operation

The integrated photocell automatically turns the fixture ON at dusk and OFF at dawn. Ensure the photocell sensor is not obstructed by objects, dirt, or debris, as this can interfere with its operation.

Once power is restored to the fixture, it will operate according to the photocell's light detection. There is no manual override for the photocell unless specified in advanced models (not applicable to this model).

6. Pangropéa

The Philips 196074 LED Flood Fixture requires minimal maintenance. Regular cleaning and inspection will ensure optimal performance and longevity.

• beberesih: Bersihkeun lénsa sareng wadahna sacara berkala nganggo lap anu lemes,amp cloth. Do not use abrasive cleaners or solvents, as these can damage the finish or lens. Ensure power is off before cleaning.
• Pamariksaan: Annually inspect the fixture for any signs of damage, loose wiring, or corrosion. Ensure mounting hardware remains secure.
• LEDs: The LED light source is integrated and not user-replaceable. Do not attempt to open the sealed LED compartment.

7. Cara ngungkulan

If you experience issues with your fixture, refer to the following troubleshooting guide:

If the problem persists after attempting these solutions, contact Philips customer support.

8. Spésifikasi

9. Garansi jeung Rojongan

Philips products are manufactured to the highest quality standards. For information regarding warranty coverage, please refer to the warranty card included with your product or visit the official Philips lighting websitus.

For technical support, troubleshooting assistance, or to inquire about replacement parts, please contact Philips customer service:

• Websitus: www.lighting.philips.com
• Telepon: Refer to your regional Philips support contact information.

Please have your model number (196074) and part number (SF100-SCT-T-G2-10-PCB-BZ) available when contacting support.