GEYA Auto Recloser with A Type RCCB RCD ELCB Self-Reclosing Device Safety Breaker

Bubuka

The GEYA Auto Recloser is an advanced safety device designed to automatically restore power after an unexpected trip of a Residual Current Circuit Breaker (RCCB) or Miniature Circuit Breaker (MCB). This device significantly reduces the need for manual intervention, thereby decreasing maintenance costs and improving operational efficiency by promptly addressing electrical faults.

It is suitable for a wide range of applications, including power grid terminal lines, unattended mobile phone base stations, elevators, air conditioners, smart homes, smart factories, and new energy vehicle charging stations.

Figure 1: GEYA Auto Recloser device.

Fitur produk

• Coupled with leakage protection switch for automatic reclosing upon unexpected RCCB trips.
• Built-in 3 reclosing attempts. If continuous closing failure occurs within 15 minutes, an alarm can be sent via an auxiliary contact.
• Features a manual/automatic selector switch for flexible operation.
• Equipped with mechanical/electronic double locking function for enhanced safety.
• Can be matched with auxiliary contact, alarm contact, shunt release, and under-voltage ngaleupaskeun.
• Closing times are reset if no trip occurs or after a manual reset within 15 minutes of successful closing.

Gambar 2: Produk leuwihview showing indicators and mode selection switch.

Setup sareng Instalasi

The GEYA Auto Recloser is designed for easy integration with existing circuit breaker systems. It can be installed alongside an RCCB or MCB on a DIN rail.

Majelis komponén

The auto recloser module (GRD9L-R) is designed to connect directly to an RCCB or MCB. Ensure proper alignment and secure connection between the units.

Figure 3: The GRD9L-R module can be installed with auxiliary components and an RCCB/MCB on a DIN rail.

Kabel Example

Follow the wiring diagram carefully to ensure correct and safe installation. Connect the power supply (L and N) to the designated terminals on the recloser and the RCCB/MCB. The load should be connected to the output terminals of the RCCB/MCB.

Gambar 4: Kelample wiring diagram for the GEYA Auto Recloser with an RCCB and an indicator light.

Pituduh Pidéo Instalasi

For a visual guide on installation and setup, please refer to the official product video below:

Parentah Operasi

Pamilihan Mode

The device features a selector switch for choosing between automatic and manual operation modes.

• Mode otomatis: The auto reclosing function is enabled. The device will automatically attempt to reclose the circuit breaker after a trip.
• Mode MANU: The auto reclosing function is disabled. The MCB/RCCB can only be opened and closed manually.

Figure 5: Detailed description of AUTO and MANU modes.

Automatic Reclosing Logic

The auto recloser is designed to attempt reclosing multiple times with increasing delays to ensure stability and identify persistent faults. The reclosing sequence is as follows:

• 1st Trip: Automatically closes after 10 seconds.
• 2nd Trip: Automatically closes after 60 seconds.
• 3rd Trip: Automatically closes after 300 seconds (5 minutes).

If continuous closing failure occurs within 15 minutes after the 3rd trip, the reclosing module will send an alarm through the auxiliary contact, and the circuit breaker will remain in the OFF/break status. The program clears accumulated closing times if the interval between two closings exceeds 15 minutes, or after a manual reset.

Figure 6: Function description and timing diagram for Auto Mode.

Figure 7: Detailed function diagram illustrating the reclosing logic and timing.

Lampu Indikator

• When powered on, the green indicator will flash for 2 seconds to wait for the power supply to stabilize, then stay on.
• If the RCCB/MCB fails to trip, the red indicator light will be on.
• During auto reclosing delay, the red indicator will flash. After the delay, it will switch on automatically and the green light will be on again.

Pangropéa

Regular maintenance ensures the optimal performance and longevity of your GEYA Auto Recloser. It is recommended to perform a monthly test to verify its functionality.

Ujian Bulanan

To perform a monthly test, ensure the device is in AUTO mode and press the "Test Monthly" button. This will simulate a leakage signal and trigger the reclosing sequence. Observe if the device trips and recloses according to the automatic reclosing logic.

Fungsi Ngonci

For safety during maintenance or inspection, the device includes a locking function. When the lock function is activated, the RCCB cannot be closed. This prevents accidental re-energization of the circuit.

Figure 8: The locking function prevents the RCCB from closing when activated, ensuring safety during circuit checks.

Pamérésan masalah

If you encounter issues with your GEYA Auto Recloser, refer to the following table for common faults and their resolutions:

Figure 9: Troubleshooting guide for common issues.

spésifikasi

Detailed technical parameters and dimensions of the GEYA Auto Recloser (GRD9L-R) are provided below:

Gambar 10: Diménsi produk dina milimeter.

Figure 11: Comprehensive technical parameters, panel diagram, and wiring diagram for GRD9L-R.

Garansi sareng Rojongan

For warranty information and technical support, please refer to the official GEYA website or contact your local distributor. Keep your purchase receipt for any warranty claims.