1. Bubuka
The LAUNCH X431 S2-2 Sensorbox is a versatile diagnostic tool designed for testing and simulating a wide range of vehicle sensors, facilitating efficient troubleshooting of Engine Control Units (ECUs). This device integrates sensor simulation, actuator testing, and multimeter functionalities, making it an essential asset for automotive repair and diagnostics.
Figure 1: LAUNCH X431 S2-2 Sensorbox with included accessories.
2. Fitur konci
- ECU Functionality Check: Determine correct ECU operation.
- Manual Waveform Data Entry: Supports custom waveform input for diagnostic flexibility.
- Sensor Simulation: Simulate various sensor working conditions without part replacement.
- Multimeter Functionality: Measures resistance, AC/DC voltage, capacitance, frequency, and pulse signals.
- Intuitive Menu: One-click access to sensors, actuators, waveforms, multimeter, and system settings.
- Customizable Waveforms: Create custom waveforms with up to 300 points, or use predefined options.
Gambar 2: Leuwihview of S2-2 Sensorbox features and integration with LAUNCH X-431 diagnostic tools.
3. Naon dina Box
The LAUNCH X431 S2-2 Sensorbox package includes the following items:
- S2-2 Module
- HT30 Test Leads
- 7-Pin Interface Adapter Cable
- Batre Clamps Kabel
- Kabel USB
- 6-Way Breakout Lead
- Multimeter Test Pen (Black + Red)
- Back Probe Pins Suite
- Adaptor kakuatan
Gambar 3: Detil view of all items included in the package.
4. Setélan
To begin using your S2-2 Sensorbox, follow these general setup guidelines:
- Sambungan Daya: Connect the S2-2 Module to a power source using the provided Power Adapter or USB cable.
- Connect to Diagnostic Tool: Connect the S2-2 Sensorbox to a compatible LAUNCH scanner (e.g., x431 PRO ELITE, X431 Throttle, X431 Pad II AE) via USB or other interface cables as required.
- Pamasangan supir: Ensure all necessary drivers are installed on your connected diagnostic tool or PC.
- Pembaruan parangkat lunak: Pariksa sareng pasang apdet parangkat lunak sacara rutin pikeun mastikeun kinerja anu optimal sareng aksés kana fitur-fitur pangénggalna.
Figure 4: S2-2 Sensorbox connected to a compatible diagnostic tablet.
4.1. Driver Installation for SmartlinkC J2534
For detailed instructions on installing the J2534 driver for SmartlinkC, please refer to the official video guide:
Video 1: LAUNCH X431 SmartlinkC J2534 driver installation guide.
5. Modeu Operasi
The S2-2 Sensorbox offers several operating modes to assist with diagnostics:
- Modeu sénsor: Simulate input signals for the automobile electronic control system, allowing adjustments to engine operation parameters.
- Actuator Mode: Simulate output control signals from the electronic control system to assess actuator performance.
- Multimeter Mode: Tés voltage, resistance, and capacitance quickly and accurately.
6. Waveform Options
The device provides flexible waveform generation capabilities:
- Defined Waveforms: Choose from 9 predefined waveforms, including sine waves, square waves, and straight lines. Adjust frequency, amplitude, offset, phase, and duty cycle as needed.
- Hand-drawn Waveforms: Create custom waveforms with up to 300 points for precise signal generation.
7. Spésifikasi
7.1. Multimeter Specifications
- DC Voltage: 0 V - 700 V
- AC Voltage: 0 V - 700 V
- Résistansi: 0 Ω - 40 MΩ
- Kapasitansi: 0 F – 100 µF (maximum 30 s measurement time)
- Dioda: 0 V - 1.5 V
- Continuity Detection: Audible signal for resistance below 30 Ω
7.2. spésifikasi umum
- Jumlah Saluran: 2
- Voltage Simulation Range: 0 ~ 20V
- Max. Kaluaran Ayeuna: 20mA
- Square Wave Signal Frequency: 0 ~ 15KHz
- Square Wave Signal Duty Cycle: 0~100%
- Sasayogian tanaga: Battery-powered for sensor output (max current 20mA), external power supply for solenoid and ignition coil output (max current 2A)
- USB: USB2.0 Type B (with charging and power supply function/5V)
- Kisaran Suhu Operasi: 0°C~50°C
- Rentang Suhu Panyimpen: -30°C~70°C
- Sertifikasi: CE, FCC, RoHS
8. Kasaluyuan
The S2-2 Sensorbox is compatible with a wide range of LAUNCH scanners, including but not limited to:
- x431 PRO ELITE
- X431 Throttle
- X431 Pad II AE
- X431 Torque
- Turbo X431
- X431 Pro3S+
- X431 PAD V
- X431 PAD 7
- X431 IMMO Elite
- X431 IMMO PLUS
9. Pangropéa
To ensure the longevity and optimal performance of your S2-2 Sensorbox:
- beberesih: Regularly clean the device and its accessories with a soft, dry cloth. Avoid using harsh chemicals or abrasive materials.
- Apdet parangkat lunak: Keep the device's software updated to benefit from new features, bug fixes, and expanded vehicle coverage.
- Panyimpenan: Store the Sensorbox in its original carrying case in a dry, cool environment when not in use.
10. Cara ngungkulan
If you encounter any issues with your S2-2 Sensorbox, please refer to the following general troubleshooting advice:
- Masalah sambungan: Ensure all cables are securely connected and that the device is properly powered. Verify Bluetooth or USB connection status on your diagnostic tool.
- Kasalahan parangkat lunak: Perform a software update. If the issue persists, consider reinstalling the drivers or contacting technical support.
- Bacaan anu salah: Check that the correct operating mode and waveform settings are selected for the specific test being performed. Ensure probes and leads are properly attached.
For more detailed troubleshooting steps, consult the comprehensive user manual provided with your device or visit the official LAUNCH support websitus.
11. Garansi jeung Rojongan
The LAUNCH X431 S2-2 Sensorbox typically comes with a 5-year warranty. Software updates are generally provided for 2 years from the date of purchase. For further support, warranty claims, or technical assistance, please refer to the contact information provided in your product packaging or visit the official LAUNCH websitus.
