AeroCool Blade ATX Semi-Tower PC Case Instruction Manual

1. Bubuka

The AeroCool Blade is an ATX semi-tower PC case designed for optimal airflow and aesthetic appeal. It features an RGB front panel with preset lighting modes, a full tempered glass side window, and ample space for component installation. This manual provides essential information for the proper setup, operation, and maintenance of your PC case.

Inpormasi Kasalametan: Always disconnect power from your system before performing any installation or maintenance. Handle components with care to avoid damage. Refer to individual component manuals for specific installation instructions.

2. Eusi Paket

• AeroCool Blade ATX Semi-Tower PC Case
• 1 x 120mm RGB Rear Fan (pre-installed)
• 3 x 120mm Front Fans (pre-installed)
• Pakakas tambahan (sekrup, standoff, kabel ties)

3. Setup jeung Instalasi

3.1 Nyiapkeun Pasualan

Carefully remove the case from its packaging. Place it on a stable, flat surface. Remove the tempered glass side panel by unscrewing the thumb screws at the rear of the case and gently pulling the panel away.

Gambar 3.1: Internal view of the AeroCool Blade PC case, illustrating the layout for component installation.

3.2 Pamasangan motherboard

1. Install the necessary motherboard standoffs into the motherboard tray according to your motherboard's form factor (ATX, Micro-ATX, Mini-ITX).
2. Pasang tameng I/O kana bukaan pungkur wadahna.
3. Taliti nempatkeun motherboard anjeun kana standoffs, aligning liang screw.
4. Ngamankeun motherboard jeung screws disadiakeun.

3.3 Pamasangan Power Supply Unit (PSU).

The AeroCool Blade supports bottom-mounted PSUs. Slide your PSU into the dedicated compartment at the bottom rear of the case. Secure it with screws from the rear of the case.

3.4 Pamasangan Girang Panyimpenan

• 3.5" HDDs: Install 3.5" hard drives into the drive cage located beneath the PSU shroud.
• SSD/HDD 2.5": Install 2.5" drives onto the dedicated mounting points on the motherboard tray or behind it.

Gambar 3.2: Bagian jero tukang view, highlighting cable management routes and 2.5-inch drive mounting locations.

3.5 Pamasangan Kartu Ékspansi (GPU)

Remove the necessary expansion slot covers from the rear of the case. Insert your graphics card or other expansion cards into the PCIe slots on your motherboard and secure them with screws.

3.6 Fan and Cooling Installation

The case comes with one 120mm RGB fan pre-installed at the rear and three 120mm fans pre-installed at the front. Ensure all fan cables are connected to appropriate headers on your motherboard or fan controller.

Figure 3.3: A 120mm RGB fan, similar to those pre-installed in the AeroCool Blade case.

3.7 Sambungan I/O Panel Hareup

Connect the front panel cables (USB 3.0, USB 2.0, HD Audio, Power Switch, Reset Switch, LED Switch, Power LED, HDD LED) to the corresponding headers on your motherboard. Refer to your motherboard manual for exact pin configurations.

4. Parentah Operasi

4.1 Powering On

Once all components are installed and connected, replace the side panel. Connect your monitor, keyboard, mouse, and power cable to the PSU. Press the Power button located on the top panel of the case to turn on your system.

Gambar 4.1: Top-hareup view of the case, indicating the location of the power button and front I/O ports.

4.2 Kontrol cahaya RGB

The AeroCool Blade features an RGB front panel. Use the dedicated LED button on the top panel to cycle through various preset lighting modes and effects. Pressing the button will change the lighting pattern or color.

Gambar 4.2: Hareupeun view of the AeroCool Blade case with its distinctive RGB lighting.

4.3 Front Panel Ports

Panel luhur nyadiakeun aksés anu merenah pikeun:

• 1 x port USB 3.0
• 2 x USB 2.0 palabuhan
• HD Audio output
• Input mikropon

Connect your USB devices, headphones, and microphone to these ports as needed.

5. Pangropéa

5.1 Lebu Filter beberesih

Regularly check and clean the dust filters to maintain optimal airflow and prevent dust buildup inside the case. Dust filters are typically located at the top, front, and bottom (under the PSU). Gently remove them and clean with compressed air or rinse with water (ensure they are completely dry before re-installation).

5.2 beberesih exterior

Lap permukaan luar wadahna ku kaén anu lemes,amp lawon. Ulah nganggo bahan kimia anu kasar atanapi bahan abrasif anu tiasa ngaruksak lapisan atanapi kaca tempered.

6. Cara ngungkulan

• Sistem Teu Hurung:
  Ensure the PSU is switched on and properly connected to the wall outlet. Verify all power cables from the PSU are correctly connected to the motherboard and components. Check the front panel power switch connection to the motherboard.
• Lampu RGB Teu Gawé:
  Ensure the RGB controller (if applicable) and fan RGB cables are securely connected. Press the LED button on the top panel to cycle through modes. If connected to a motherboard header, check motherboard software settings.
• Penggemar Teu Diputer:
  Verify that all fan power cables are securely connected to the motherboard fan headers or a fan controller. Check BIOS/UEFI settings for fan speed control.
• Panel hareup USB/Audio Teu Gawé:
  Ensure the USB and HD Audio cables from the front panel are correctly connected to the corresponding headers on your motherboard.

7. Spésifikasi

Figure 7.1: Dimensions of the AeroCool Blade PC Case.

8. Garansi jeung Rojongan

Kanggo inpormasi garansi sareng dukungan téknis, mangga tingal situs resmi AeroCool. websitus atanapi ngahubungan pangecér lokal Anjeun. Simpen bukti pameseran anjeun pikeun klaim garansi.

Inpormasi kontak: Pikeun pitulung salajengna, mangga buka www.aerocool.io.