BLAUPUNKT AMP1604 4-Channel Full-Range Car AmpManual Pamaké lifier

1. Bubuka sarta Produk Leuwihview

BLAUPUNKT AMP1604 mangrupakeun 4-kanal, rentang pinuh amplifier designed to enhance the audio system in your vehicle. This amplifier provides increased power output for both speakers and subwoofers, offering flexibility in configuring your car audio setup. It features a compact design suitable for various installation locations.

Gambar 1.1: Top view tina BLAUPUNKT AMP1604 amppangagung.

2. Émbaran Kasalametan

Mangga baca sadaya parentah kalawan saksama sateuacan masang sareng ngoperasikeun ieu amplifier. Failure to follow these instructions may result in damage to the ampkacilakaan, kandaraan, atawa cilaka pribadi.

• Pamasangan profésional disarankeun: Due to the complexity of car audio systems, professional installation is recommended.
• Sambungan Kakuatan: Ensure all power connections are secure and properly fused to prevent short circuits and fire hazards. Disconnect the vehicle's battery before starting installation.
• Ventilasi: Pasang éta ampLifier di lokasi anu ngamungkinkeun pikeun ventilasi nyukupan pikeun nyegah overheating.
• Wiring: Paké wiring gauge luyu pikeun kakuatan, taneuh, sarta sambungan speaker.
• Uap: Hindarkeun ngalaan éta ampLifier kana Uap atanapi suhu ekstrim.

3. Eusi Paket

Pastikeun yén sadaya item aya dina bungkusan:

• BLAUPUNKT AMP1604 Amppangagung
• Manual pangguna (dokumén ieu)

4. Fitur Produk

BLAUPUNKT AMP1604 amplifier ngawengku fitur konci ieu:

• Amplifier Kelas: AB
• 4/3/2 Channel Operation
• Max. Kakuatan Kaluaran: 1600W
• RMS Power (4 Ohms): 55W x 4
• RMS Power (2 Ohms): 79W x 4
• Frequency Response: 10Hz - 30kHz
• Crossover Frequency: 50Hz - 250Hz
• Crossover Slope (dB/oct): 8-10dB/oct
• Signal-To-Noise Ratio: ≥96dB
• Voltage Suplai: 11-15V DC
• Gain Adjust: 200mV ~ 8V
• Total distorsi harmonik: ≤0.05%
• Input RCA: 4 Saluran
• sekering: 25A x 2
• Ukuran: 11 x 7.4 x 2.2 cm

Figure 4.1: Detailed features and specifications of the AMP1604.

5. Setup jeung Instalasi

Proper installation is crucial for optimal performance and safety. Consult a professional if you are unsure about any steps.

5.1 Pamasangan Amppangagung

• Pilih tempat anu aman, garing, sareng ventilasi anu cekap. Ulah dipasang dina karpét atanapi di rohangan anu katutup tanpa aliran hawa.
• Pastikeun permukaan anu dipasang cukup kuat pikeun ngadukung ampbeurat liifier.
• Use appropriate hardware to secure the amplifier firmly to prevent movement during vehicle operation.

5.2 Sambungan Wiring

Refer to the diagrams below for proper wiring connections. Always disconnect the vehicle's negative battery terminal before making any power connections.

Figure 5.1: Power and speaker terminal connections.

• Power (B+ / +12V): Connect to the positive terminal of the vehicle's battery using a heavy-gauge power cable. Install an inline fuse (not supplied) within 18 inches of the battery.
• Taneuh (GND): Nyambung ka bersih, permukaan logam unpainted tina chassis wahana. Pastikeun sambungan listrik padet.
• Jauh (REM): Connect to the remote turn-on lead from your head unit. This wire turns the amphurungkeun sareng pareumkeun liifier nganggo head unit.
• Kaluaran Spiker (CH1-CH4): Connect your speakers to the corresponding terminals. Observe correct polarity (+ and -).
• RCA Inputs (CH1-CH4): Sambungkeun kabel RCA tina unit sirah anjeunamp outputs kana ampinputs RCA lifier urang.
• High-Level Inputs (HI INPUT): If your head unit does not have RCA outputs, use the high-level inputs. Connect speaker wires from your head unit directly to these inputs.

6. Parentah Operasi

Sakali dipasang, saluyukeun ampsetélan lampu pikeun kinerja audio anu optimal.

Gambar 6.1: Amppanel kontrol lifier.

• Input Mode (2CH/4CH): Select the input mode based on how many RCA input channels are connected from your head unit. If using 2 RCA inputs for all 4 amplifier channels, select 2CH. If using 4 RCA inputs, select 4CH.
• Gain Control (Min/Max): Atur kontrol gain pikeun cocog sareng voltase kaluarantage tina head unit anjeun. Mimitian ku gain minimal teras laun-laun tambahkeun dugi ka volume anu dipikahoyong kahontal tanpa distorsi.
• Crossover Settings (HPF/LPF/FULL):
  • HPF (Saringan High Pass): Allows frequencies above the set point to pass through. Useful for speakers to prevent low bass distortion.
  • LPF (Low Pass Filter): Allows frequencies below the set point to pass through. Useful for subwoofers.
  • FULL: Ngidinan sadaya frékuénsi nembus.
• Crossover Frequency (50Hz - 250Hz): Adjust the cutoff frequency for the HPF or LPF as needed for your speakers or subwoofers.
• Bass EQ (0dB - 18dB): Provides a bass boost at a specific frequency. Use sparingly to avoid distortion.

7. Pangropéa

Pangropéa rutin ngabantosan mastikeun umur panjang sareng kinerja anjeun amppangagung.

• beberesih: Ngabersihan périodik ampexterior lifier urang ku lemes, lawon garing. Ulah make bahan kimia kasar atawa cleaners abrasive.
• Cék sambungan: Annually, inspect all wiring connections (power, ground, remote, RCA, speaker) to ensure they are secure and free from corrosion.
• Ventilasi: Pastikeun yén ampSirip-sirip pendingin lifier bébas tina lebu sareng runtah pikeun ngajaga disipasi panas anu leres.

8. Cara ngungkulan

Upami anjeun ngalaman masalah sareng anjeun ampLifier, tingal masalah sareng solusi umum ieu:

9. Spésifikasi

10. Garansi jeung Rojongan

For warranty information and technical support, please refer to the documentation provided with your purchase or visit the official BLAUPUNKT websitus. Simpen bukti pameseran anjeun pikeun klaim garansi.