SINOTIMER TM618 -7 Days Programmable Weekly Timer Module

1. Langkungview

The SINOTIMER TM618 timer module is designed to automatically control the power supply to various electrical apparatus, such as streetlights, neon signs, billboards, and other appliances, based on a preset time schedule. This digital timer switch features a rechargeable internal battery to maintain program settings during power outages.

Gambar 1.1: Hareupeun view of the TM618 Timer Module.

2. Fitur konci

• Desain kompak sareng hemat rohangan.
• Engineered with advanced digital timing technology.
• High functionality for precise time control.
• Built-in rechargeable battery for program retention.
• Multiple ON/OFF programs for weekly scheduling.

3. Setup jeung Instalasi

3.1. Diagram Kabel

Proper wiring is crucial for the safe and correct operation of the TM618 timer module. Refer to the diagram below for connection details. Ensure power is disconnected before performing any wiring.

Figure 3.1: Wiring Terminals and Specifications.

• Input (200-250VAC): Connect your main power supply to terminals 1 and 2.
• Output (16 AMP / 250VAC, 20 AMP @30 VDC): Terminals 3, 4, and 5 are for the controlled output. Terminal 3 is common, Terminal 4 is normally open (NO), and Terminal 5 is normally closed (NC). Connect your load to the appropriate terminals based on your application (e.g., between 3 and 4 for normally off, turning on when timed).

3.2. Initial Power-Up and Battery

Upon initial power-up, the timer's internal rechargeable battery (40mAh) will begin charging. This battery saves your programmed settings during power interruptions. Allow the unit to be powered for at least 30 minutes for the battery to gain sufficient charge before programming or disconnecting power.

Figure 3.2: Internal 40mAh Rechargeable Battery.

Figure 3.3: TM618 Operating Voltage (220V AC shown).

4. Parentah Operasi

The TM618 timer allows for precise control with up to 16 ON/OFF programs per day or week. The buttons on the front panel are used for setting the time and programs.

Figure 4.1: Timer Module with Manual.

4.1. Nyetél Waktos Ayeuna

1. Pencét éta JAM button and hold it.
2. Bari nyekelan JAM, pencét MINGGU pikeun ngeset dinten ayeuna dina saminggu.
3. Bari nyekelan JAM, pencét JAM pikeun ngeset jam ayeuna.
4. Bari nyekelan JAM, pencét MIN pikeun nyetél menit ayeuna.
5. Ngaleupaskeun JAM button. The time is now set.

4.2. Programming Waktu ON/OFF

The timer supports up to 16 ON/OFF programs. Each program consists of an ON time and an OFF time.

1. Pencét éta PROG tombol sakali. Layar bakal némbongkeun "1 ON".
2. Pencét MINGGU to select the day(s) for this program (e.g., MO, TU, WE, TH, FR, SA, SU, or combinations like MO-FR, SA-SU, MO-SA, etc.).
3. Pencét JAM pikeun nyetel jam ON anu dipikahoyong.
4. Pencét MIN pikeun nyetel menit ON anu dipikahoyong.
5. Pencét PROG deui. Layarna bakal némbongkeun "1 OFF".
6. Repeat steps 2-4 to set the desired OFF day(s), hour, and minute for this program.
7. Pencét PROG to advance to the next program ("2 ON") or to exit programming mode if no more programs are needed.
8. To clear a program, press PANGELING bari viewing the specific ON or OFF program you wish to clear.

4.3. Manual Override

Pencét éta MANUAL button to cycle through different operating modes:

• OTOMATIS ON: The timer is currently ON and will follow the programmed schedule.
• Otomatis Pareum: The timer is currently OFF and will follow the programmed schedule.
• ON: The timer is forced ON, overriding any programs.
• Pareuman: The timer is forced OFF, overriding any programs.

4.4. Recall Function

The PANGELING button (often marked 'R' or 'RESET') is used to clear specific program settings or to reset the timer. A small pinhole button (R) is typically used for a full reset, which clears all programs and resets the time.

5. Pangropéa

5.1. Kaperawatan batré

The TM618 features a built-in rechargeable battery. To ensure its longevity and proper function, keep the timer connected to power for regular charging. If the timer is stored for extended periods without power, the battery may discharge, requiring a full charge upon reconnection.

5.2. beberesih

Clean the exterior of the timer module with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these can damage the plastic casing or display. Ensure no liquids enter the device.

6. Cara ngungkulan

• Tampilan kosong: Check power connections. Ensure the unit has been powered for at least 30 minutes to charge the internal battery.
• Programs not executing: Verify that the current time is set correctly. Check that the timer is in "AUTO ON" or "AUTO OFF" mode, not forced ON/OFF. Review your programmed ON/OFF times for accuracy.
• Timer not responding to buttons: Perform a full reset using the small 'R' pinhole button. If issues persist, ensure proper power supply.

7. Spésifikasi

7.1. Diménsi

Figure 7.1: Front Dimensions.

Figure 7.2: Side Dimensions.

8. Garansi jeung Rojongan

For information regarding product warranty, technical support, or service, please refer to the documentation provided with your purchase or contact your retailer. Keep your proof of purchase for any warranty claims.