Okin Lift Chair Remote Control User Manual

1. Produk Langkungview

This manual provides instructions for the Okin 2 Button 5 Pin Power Recliner Switch Hand Control, designed as a universal replacement for lift chairs and electric sofas. It ensures seamless operation and control for your electric furniture.

Fitur konci:

• Wired Recliner Switch Controller: Cable length 68.9 inches (175 cm).
• 5-pin round plug with a 90-degree L-shape connector.
• Universal compatibility with OKIN Single Motor electric furniture and most common brand recliner motors.
• Durable and ergonomic design for user comfort.

Figure 1: Okin 2 Button 5 Pin Power Recliner Hand Control with coiled cord and 5-pin connector.

Figure 2: The Okin remote control showing the full length of its extended cable.

2. Émbaran Kasalametan

Please read and understand all safety instructions before using the product to prevent injury or damage.

• Do not exceed the maximum weight limit of the recliner.
• Ensure the recliner is properly grounded.
• Be cautious when operating the recliner to avoid pinching fingers or other body parts.
• Salawasna pegatkeun sambungan kakuatan saméméh ngajalankeun sagala pangropéa atawa instalasi.

3. Setup jeung Instalasi

The recliner chair controller is designed for easy installation. Follow these steps to replace your old or broken remote.

1. Identipikasi Panyambungna: Before purchase and installation, carefully check the plug of your existing remote to ensure it matches the 5-pin round plug and 90-degree L-shape connector of this replacement.

angka 3: Tutup-up view of the 5-pin round plug connector.
2. Pegatkeun Daya: Unplug your recliner from the wall outlet to ensure safety during installation.
3. Locate Existing Connection: Find where your current remote control cable connects to the recliner's motor or control box.
4. Pegatkeun sambungan Remote Old: Carefully unplug the old remote control.
5. Sambungkeun Jauh Anyar: Align the 5-pin round plug of the new Okin remote with the corresponding port on your recliner's motor or control box. Push firmly until it clicks into place.


Figure 4: The Okin remote control with its coiled cord and 5-pin connector, ready for installation.

6. Kabel Aman: Ensure the cable is not pinched or tangled.
7. Mulangkeun Daya: Plug your recliner back into the wall outlet.

4. Parentah Operasi

The Okin lift chair remote features a simple two-button interface for intuitive control of your recliner's movement.

Gambar 5: Hareupeun view of the Okin 2-button remote control.

• Up Button (Top Button): Press and hold the top button to raise the footrest and/or lift the chair to an upright or standing assist position. Release the button to stop movement.
• Down Button (Bottom Button): Press and hold the bottom button to lower the footrest and/or recline the chair to a seated or lying position. Release the button to stop movement.

The remote allows for precise control; release the button at any desired position to stop the chair's movement.

5. Pangropéa

To ensure the longevity and proper functioning of your Okin remote control, follow these simple maintenance guidelines:

• beberesih: Wipe clean with a soft, dry cloth. Do not use abrasive cleaners or immerse the remote in water.
• Perawatan kabel: Avoid kinking or excessively bending the cable. Ensure it is not caught under the recliner or furniture.
• Panyimpenan: When not in use, store the remote in a safe place where it won't be damaged or stepped on.

6. Cara ngungkulan

If you experience issues with your Okin lift chair remote, try the following troubleshooting steps:

• Jauh Teu Ngabales:
  • Ensure the recliner is properly plugged into a working power outlet.
  • Check all cable connections, especially the 5-pin plug, to ensure they are secure and fully inserted.
  • Inspect the cable for any visible damage, cuts, or pinches.
• Operasi intermittent:
  • Verify that the 5-pin connector is clean and free of debris.
  • Gently wiggle the connector at the motor to see if it restores function, indicating a loose connection.
• Tombol Teu Gawé:
  • Ensure the buttons are not stuck or obstructed.
  • If only one button is not working, the remote may need replacement.

Upami léngkah-léngkah ieu henteu ngabéréskeun masalah, mangga ngahubungi dukungan palanggan.

7. Spésifikasi

Figure 6: Detail of the product label, showing model number (1.11-186.30) and power specifications (DC 29V 2A).

8. Garansi jeung Rojongan

Okin stands behind the quality of its products. While specific warranty details are not provided in this manual, customer satisfaction is guaranteed.

For any questions, issues, or support needs regarding your Okin Lift Chair Remote, please contact our customer service team. They are ready to help resolve any concerns you may have.

You can often find contact information on the product packaging or the official Okin websitus.