DIGITEN DHTC-1011 Temperature and Humidity Controller

1. Produk Langkungview

The DIGITEN DHTC-1011 is a versatile plug-and-play temperature and humidity controller designed to maintain precise environmental conditions. It features dual relay outputs, allowing simultaneous control of heating/cooling and humidifying/dehumidifying devices. Its large LCD screen and simple 3-button interface ensure ease of use for various applications, including home brewing, fermentation, greenhouses, terrariums, and reptile enclosures.

Figure 1: DIGITEN DHTC-1011 Controller with its main components.

Figure 2: Key features of the DHTC-1011, including dual outlets and various control modes.

2. Setup jeung Instalasi

Follow these steps to set up your DHTC-1011 controller:

1. Buka bungkus Alat: Carefully remove the controller, sensor, and power cord from the packaging.
2. Connect the Sensor: Plug the sensitive temperature and humidity probe into the designated port on the top of the controller. Ensure it is securely connected.

Figure 3: Connecting the sensitive temperature and humidity probe.
3. Posisi sénsor: Place the sensor in the environment where you wish to monitor and control temperature and humidity. Ensure it is not directly exposed to heat sources, cold drafts, or excessive moisture that could affect readings.
4. Sambungkeun Perkakas: Plug your heating/cooling device into the 'TEMPERATURE' outlet and your humidifying/dehumidifying device into the 'HUMIDITY' outlet on the power strip.


Figure 4: Dual outlets for temperature and humidity control.

5. Daya Hurung: Plug the controller's main power cord into a standard electrical outlet. The LCD screen will illuminate, displaying current temperature and humidity readings.

3. Parentah Operasi

The DHTC-1011 offers intuitive controls for setting your desired environmental parameters.

3.1. Operasi dasar

• The large LCD screen displays the current temperature and humidity.
• The 'SET' button is used to enter programming mode.
• The 'Up' and 'Down' arrow buttons are used to adjust values and navigate through settings.

3.2. Setting Temperature and Humidity

1. Press and hold the 'SET' button for 3 seconds to enter the temperature setting mode. The temperature display will flash.
2. Use the 'Up' and 'Down' arrows to set your desired temperature.
3. Press 'SET' again to confirm the temperature and move to the humidity setting mode. The humidity display will flash.
4. Use the 'Up' and 'Down' arrows to set your desired humidity.
5. Press 'SET' one more time to confirm the humidity and exit programming mode. The settings will be saved automatically.

3.3. Setélan Canggih

The controller supports various advanced settings for precise control:

• Pilihan Unit Suhu: Easily switch between Celsius (℃) and Fahrenheit (℉) display. Refer to the detailed manual for specific button combinations.
• Kalibrasi: Calibrate the temperature and humidity readings if necessary to match external reference instruments.
• Tunda kompresor: Set a delay for cooling devices to protect the compressor from frequent on/off cycles.
• High/Low Alarms: Configure high or low temperature and humidity alarms to alert you when conditions fall outside your desired range.
• Nyimpen Setélan: The device is designed to save your original setting values in case of accidental power-off, ensuring continuity of operation.

Gambar 5: Kelample setup showing the controller in use with a humidifier and an enclosure.

4. Pangropéa

Proper maintenance ensures the longevity and accuracy of your DHTC-1011 controller:

• beberesih: Wipe the controller and sensor with a soft, dry cloth. Do not use abrasive cleaners or immerse the unit in water.
• Perawatan sénsor: Keep the sensor clean and free from dust or debris. Avoid bending or damaging the sensor cable.
• Panyimpenan: Upami nyimpen alat kanggo waktos anu panjang, pegatkeun sambungan tina kakuatan teras simpen di tempat anu tiis sareng garing.

5. Cara ngungkulan

If you encounter issues with your DHTC-1011, refer to the following common troubleshooting tips:

• Alat Teu Dihurungkeun: Ensure the power cord is securely plugged into a live electrical outlet. Check the outlet with another device to confirm it has power.
• Bacaan teu akurat: Verify the sensor is clean and properly connected. If readings appear consistently off, consider performing a calibration as described in the advanced settings section.
• Connected Appliance Not Activating: Check that the appliance is correctly plugged into the 'TEMPERATURE' or 'HUMIDITY' outlet and that the controller's settings (set point, differential) are configured to trigger the appliance. Ensure the appliance itself is functional.
• Controller Beeping: A continuous beeping sound typically indicates an alarm condition (e.g., temperature or humidity outside the set range). Check the display for alarm indicators and adjust conditions or settings as needed.
• Setélan Henteu Simpen: The DHTC-1011 is designed to save settings automatically upon exiting programming mode. Ensure you press 'SET' to confirm changes before unplugging the device.

For persistent issues, please contact DIGITEN customer support.

6. Spésifikasi

7. Garansi jeung Rojongan

7.1. Émbaran jaminan

DIGITEN provides a one-year warranty term for any product quality problems. Please retain your proof of purchase for warranty claims.

7.2. Rojongan Palanggan

For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact DIGITEN customer support through the official DIGITEN store on Amazon or their official website. Provide your product model number (DHTC-1011) and a detailed description of the issue for efficient service.