Bubuka
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Faultless Ball Satin Stainless Steel Entry Knob and Single Cylinder Deadbolt. Please read these instructions carefully before installation and use to ensure proper function and longevity of your lockset.
Émbaran Kasalametan
- Always wear appropriate safety gear, such as gloves and eye protection, during installation.
- Pastikeun yén sadaya komponén dipasang sacara aman sateuacan dianggo.
- Do not use excessive force when operating the lockset.
- Keep keys in a safe and accessible location, separate from the door.
Eusi pakét
Paket anjeun kedah ngandung barang-barang ieu:
- 2 x Keyed Entry Ball Knobs
- 2 x Single Cylinder Deadbolts
- 4 x KW1 Keys
- Adjustable Latches (for both knob and deadbolt)
- Pelat Tembakan
- Pamasangan screws
- Citakan Instalasi (upami kalebet)
Image: All components of the Faultless Ball Satin Stainless Steel Entry Knob and Single Cylinder Deadbolt set, including two knobs and two deadbolts with their respective latches and strike plates.
Setup sareng Instalasi
Alat anu diperyogikeun:
- Phillips Kepala Obeng
- Pita Ukur
- Pensil
- Bor (upami peryogi persiapan panto énggal)
- Wood Chisel (if new door preparation is needed)
Léngkah-léngkah pamasangan:
- Nyiapkeun lawang: Ensure your door has the correct bore holes (typically 2-1/8 inches for the lock body and 1 inch for the latch) and backset (2-3/8 inches or 2-3/4 inches). Use the provided template if drilling new holes.
- Pasang Latch: Insert the latch into the edge bore hole of the door. Ensure the bevel of the latch bolt faces the door frame. Secure with two small screws. Adjust the backset if necessary by twisting the latch mechanism.
- Install the Exterior Knob/Deadbolt: Place the exterior portion of the knob/deadbolt through the large bore hole, ensuring the spindle or tailpiece aligns with the latch mechanism.
- Install the Interior Knob/Deadbolt: Position the interior portion of the knob/deadbolt, aligning it with the exterior portion and the latch. Secure with the long mounting screws provided, tightening evenly.
- Pasang Strike Plate: Mark the position of the latch bolt on the door frame. Chisel out a shallow recess for the strike plate and secure it with screws. Ensure the latch bolt engages smoothly.
- Operasi tés: Close the door and test the knob and deadbolt with the key from both inside and outside to ensure smooth operation.
Parentah Operasi
Keyed Entry Knob:
- Pikeun Ngonci ti Luar: Insert the key and turn it to lock the knob. Remove the key.
- Pikeun muka konci ti luar: Insert the key and turn it to unlock the knob.
- Pikeun Ngonci ti Jero: Press or turn the button/thumbturn on the interior knob.
- Pikeun muka konci ti jero: Turn the interior knob or button/thumbturn.
Silinder Tunggal Deadbolt:
- Pikeun Ngonci ti Luar: Insert the key and turn it to extend the deadbolt. Remove the key.
- Pikeun muka konci ti luar: Insert the key and turn it to retract the deadbolt.
- Pikeun Ngonci ti Jero: Turn the thumbturn on the interior side to extend the deadbolt.
- Pikeun muka konci ti jero: Turn the thumbturn on the interior side to retract the deadbolt.
Pangropéa
- beberesih: Clean the lockset regularly with a soft, damp cloth. Avoid abrasive cleaners or harsh chemicals, as these can damage the satin stainless steel finish.
- Lubrication: Periodically apply a small amount of graphite lubricant or a silicone-based spray to the keyway and latch mechanism to ensure smooth operation. Do not use oil-based lubricants as they can attract dirt.
- sekrup tightness: Check and tighten all mounting screws periodically to ensure the lockset remains securely attached to the door.
Pamérésan masalah
| Masalah | Mungkin Cukang lantaranana | Solusi |
|---|---|---|
| Koncina teu muter atawa kaku. | Kokotor dina alur konci, konci nu geus aus, atawa silinderna teu rata. | Clean keyway with graphite lubricant. Try a spare key. Check for proper cylinder alignment. |
| Latch bolt does not retract/extend fully. | Misaligned latch, bent components, or debris. | Check latch alignment and screw tightness. Clear any obstructions. Lubricate the latch mechanism. |
| Door does not close properly with lock engaged. | Misaligned strike plate or door frame issues. | Adjust the strike plate position. Inspect the door frame for warping or damage. |
| Knob/Deadbolt feels loose. | screws ningkatna leupas. | Tighten the mounting screws evenly. Do not overtighten. |
spésifikasi
- Jenis produk: Keyed Entry Knob and Single Cylinder Deadbolt
- model: B36L1BD
- Bahan: Baja stainless, Logam
- rengse: Satin Stainless Steel
- Kelas: 3 Grade (Residential)
- Panto Handing: Leungeun katuhu
- Backset adjustable: 2-3/8 inci (60mm) atanapi 2-3/4 inci (70mm)
- Kisaran Ketebalan Pintu: 1-3/8 inches (35mm) to 1-3/4 inches (44mm)
- Alur konci: KW1
- Keys Included: 4
- Ukuran produk: Kira-kira 3.3 x 12.4 x 9.8 inci (8.4 x 31.5 x 24.9 cm)
- Pamakéan Indoor/Outdoor: Luar
Garansi sareng Rojongan
For warranty information, please refer to the documentation provided at the time of purchase or contact the retailer/manufacturer directly. Specific warranty terms may vary.
For technical support or further assistance, please contact the customer service department of your retailer or the manufacturer, Overstock.
