Bubuka
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Ikea KALLROR 503.570.02 Stainless Steel Cabinet Handles. Please read these instructions carefully before proceeding with installation to ensure proper and safe use.
Produk Leuwihview
The Ikea KALLROR 503.570.02 handles are designed to offer a modern aesthetic and functional grip for your kitchen cabinets or drawers. This set includes two handles and all necessary screws for a complete installation.
This image displays two sleek, cylindrical stainless steel cabinet handles, along with four silver screws. The handles have a brushed finish, and each handle is shown with two mounting posts. The screws are designed to secure the handles to cabinet doors or drawers.
spésifikasi
| Nomer modél | 503.570.02 |
| merek | Ikea |
| Quantity per set | 2 cecekelan |
| Panjang cecekelan | 213 mm |
| Nanganan Jerona | 38 mm |
| Hole Spacing (center-to-center) | 160 mm |
| Drilled Hole Diameter | 5 mm |
| Kandel Panto Cocog | 16 mm nepi ka 21 mm |
| Handle/End Cap Material | Beusi sténless |
| Plastic Parts Material | Poliétilén Plastik |
| Komponén Kaasup | Perangkat Keras Pemasangan (sekrup) |
| Beurat | 170 gram |
Setup sareng Instalasi
Installing your Ikea KALLROR cabinet handles is a straightforward process. Follow these steps carefully for a secure attachment.
Pakakas Diperlukeun
- Bor
- Mata bor (diaméter 5 mm)
- Pita ukur atawa penggaris
- Pensil
- Obeng (disarankeun sirah Phillips)
Léngkah-léngkah Instalasi
- Ukur sareng Tanda: Carefully measure and mark the desired position for the handle on your cabinet door or drawer front. Ensure the marks for the two screw holes are precisely 160 mm apart (center-to-center).
- liang bor: Using a 5 mm drill bit, carefully drill through the cabinet door or drawer front at the marked positions. Ensure the holes are straight and clean.
- Gantelkeun gagang: Align the handle with the drilled holes. Insert the provided screws from the inside of the cabinet door or drawer through the drilled holes and into the handle posts.
- Cecekelan Aman: Tighten the screws firmly with a screwdriver until the handle is securely attached. Ulah overtighten, as this may damage the cabinet material.
- Ulang deui: Repeat the process for the second handle if installing a set.
Important: These handles are suitable for door thicknesses between 16 mm and 21 mm. Verify your cabinet door thickness before drilling.
Operasi
The Ikea KALLROR cabinet handles are designed for simple and reliable operation. Grasp the handle firmly to open or close cabinet doors and drawers as needed.
Pangropéa
To ensure the longevity and appearance of your stainless steel handles, follow these maintenance guidelines:
- beberesih: Lap sacara rutin nganggo kaén nu lemes,amp cloth. For stubborn marks, use a mild detergent solution. Avoid abrasive cleaners, scouring pads, or chemical solvents, as these can damage the stainless steel finish.
- Pangeringan: Always dry the handles thoroughly after cleaning to prevent water spots and maintain their luster.
- Pamariksaan: Periodically check the screws for tightness. If a handle feels loose, gently tighten the screws with a screwdriver.
Pamérésan masalah
Handle is Loose
If the handle feels loose, gently tighten the screws from the inside of the cabinet door or drawer. Ensure not to overtighten.
Kasesahan Masang
Ensure the drilled holes are precisely 160 mm apart (center-to-center) and that the drill bit used was 5 mm in diameter. Verify your cabinet door thickness is within the specified 16-21 mm range.
Ngarojong
For further assistance or inquiries regarding your Ikea KALLROR cabinet handles, please refer to the official Ikea websitus atanapi hubungi layanan palanggan Ikea sacara langsung.
