MOTOPOWER MP0514A-UK 12V Digital Battery and Alternator Tester Instruction Manual

1. Produk Langkungview

The MOTOPOWER MP0514A-UK is a 12V digital battery and alternator tester designed for quick and accurate assessment of vehicle battery health and charging system performance. It features an LCD display for voltage readings and LED indicators for battery and alternator status.

1.1. Naon dina Box

• MOTOPOWER MP0514A-UK Tester Body

2. Émbaran Kasalametan

• Always wear appropriate eye protection when working with vehicle batteries.
• Pastikeun ventilasi anu leres di daérah damel.
• Hindarkeun kontak sareng asam batré.
• The device features reverse connection and over-voltage panyalindungan pikeun operasi aman.
• Entong nganggo panguji upami katingalina ruksak.

3. Setup jeung Connection

The MOTOPOWER MP0514A-UK is designed for easy connection to 12V vehicle batteries and charging systems.

1. Ensure the vehicle engine is off before connecting the tester for battery status check.
2. Nyambungkeun beureum clamp ka terminal positif (+) batré 12V.
3. Nyambungkeun hideung clamp ka terminal négatif (-) batré 12V.
4. The digital display will illuminate, showing the current battery voltage. If connected in reverse, a "REVERSE" LED indicator will light up.

4. Operasi

4.1. Battery Status Test

To check the battery's state of charge:

1. Ensure the tester is connected correctly to the battery terminals with the vehicle engine off.
2. Baca voltage displayed on the digital screen.
3. Observe the LED indicators on the left side of the tester (labeled "STATE OF CHARGE"):
   • FULL: Batré dicas pinuh.
   • MEDIUM: Battery has a medium charge.
   • RENDAH: Battery charge is low.
   • KOSONG: Battery is discharged and may need charging or replacement.

4.2. Alternator Output Test

To check the alternator's charging performance:

1. Ensure the tester is connected correctly to the battery terminals.
2. Start the vehicle engine and let it run at idle.
3. Observe the LED indicators on the right side of the tester (labeled "Alternator"):
   • TINGGI: Alternator output is too high.
   • alus: Alternator is charging correctly.
   • maot: Alternator is not charging or output is too low.
4. The digital display will show the charging voltage.

5. Cara ngungkulan

• No Display/No LEDs:
  • Pariksa lamun clamps disambungkeun aman ka terminal batré.
  • Ensure the battery has at least 4V DC. If voltage is below 4V, the display will show "LO".
  • Verify correct polarity. If connected in reverse, the "REVERSE" LED should light up.
• Display shows "LO":
  • Batré voltage is below the measurable range of 4V DC. The battery is severely discharged or faulty.
• Layar nunjukkeun "HI":
  • Voltage is above the measurable range of 20V DC. This indicates an over-voltage condition, potentially from a faulty charging system.
• Bacaan teu akurat:
  • Pastikeun clamps are clean and have good contact with battery terminals.
  • Test on a different 12V battery to confirm device functionality.

6. Pangropéa

• Clean the tester body and clamps kalawan lemes, lawon garing sanggeus unggal pamakéan.
• Store the device in a dry, cool place away from direct sunlight and corrosive materials.
• Ulah neuleumkeun alat dina cai atawa cairan séjén.
• Pariksa kabel sareng cl sacara rutinamps for any signs of damage.

7. Spésifikasi

8. Garansi jeung Rojongan

MOTOPOWER offers a two-year warranty and lifetime service for this product. To activate your warranty, please register your product on the official MOTOPOWER website. For technical support or warranty claims, please contact MOTOPOWER customer service through their official channels.

Kanggo inpo nu leuwih lengkep, buka di MOTOPOWER Store on Amazon.