ONKRON G120-BLK Single Monitor Wall Mount Instruction Manual
Model: G120-BLK
Bubuka
This manual provides detailed instructions for the safe and proper installation, operation, and maintenance of your ONKRON G120-BLK Single Monitor Wall Mount. Please read this manual thoroughly before installation and retain it for future reference.
Image: The ONKRON G120-BLK Single Monitor Wall Mount, a black articulating arm designed for wall mounting.
Émbaran Kasalametan
WARNING: Improper installation or use of this product may result in serious injury or damage. If you do not understand these instructions or have doubts about the safety of the installation, please contact a qualified installer or ONKRON customer support.
- Pastikeun permukaan pemasangan tiasa nahan beurat gabungan tina dudukan sareng monitor anjeun kalayan aman.
- Ulah ngaleuwihan kapasitas beurat maksimum 17.6 lbs (8 kg).
- Dudukan ieu dirancang pikeun monitor ukuran antara 13 sareng 34 inci.
- Always use the provided hardware. If any parts are missing or defective, contact ONKRON for replacement.
- Exercise caution when handling the gas spring mechanism. The spring is under tension and can cause injury if not handled correctly. Do not remove plastic covers over the main poles as they are for protection.
- Jauhkeun barudak sareng piaraan salami instalasi.
Eusi pakét
Pariksa yén sadaya komponén aya sateuacan ngamimitian pamasangan.
Image: All components included in the ONKRON G120-BLK package, including the mount, various screws, washers, wall anchors, and an Allen key.
- Monitor Wall Mount Assembly
- Lempeng VESA
- Piring Tembok
- Mounting Hardware (screws, anchors, washers for various VESA sizes)
- Konci Allen (6mm)
- Instruksi Manual
Setup sareng Instalasi
Follow these steps carefully for a secure installation. It is recommended to have a second person assist during monitor attachment.
Pituduh Pidéo Instalasi
Video: An official ONKRON instruction video demonstrating the installation process for the G120-B monitor mount.
Lengkah 1: Nyirian liang bor
- Determine the desired mounting location on your wall. Ensure it is a solid surface (e.g., wood stud, concrete) capable of supporting the weight.
- Hold the wall plate against the wall at the desired height and use a pencil to mark the drill hole locations.
Image: The ONKRON G120-BLK monitor mount securely installed on a brick wall, demonstrating a typical mounting scenario.
Lengkah 2: Pasang Gunung
- Drill pilot holes at the marked locations. The drill bit size will depend on your wall material and the anchors used.
- Amankeun pelat témbok kana témbok nganggo sekrup sareng jangkar anu pas. Pastikeun éta napel pageuh tur tingkat.
Step 3: Attaching the Monitor to the Mount
- Attach the VESA plate to the back of your monitor using the correct screws (M4 or M6) that fit your monitor's VESA pattern (75x75mm or 100x100mm). Ensure the screws are tightened securely but do not overtighten.
- Carefully lift the monitor and slide the VESA plate onto the arm's mounting head. Ensure it clicks into place or is secured with the provided locking mechanism.
Image: Diagram illustrating VESA 75x75mm and 100x100mm mounting patterns, compatible screen diagonal (13"-34"), and load capacity (2.2-17.6 lbs).
Step 4: Adjusting for Monitor Weight (Gas Spring Tension)
The gas spring tension must be adjusted after the monitor is attached to ensure it holds its position. If the monitor sags or springs up, adjust the tension.
- Locate the gas spring adjustment screw on the arm.
- Use the provided Allen key to turn the screw:
- Giliran counter-jarum jam for lighter screens (to reduce tension).
- Giliran saarah jarum jam for heavier screens (to increase tension).
- Adjust gradually until the monitor stays in the desired vertical position when released.
Image: Close-up of the gas spring adjustment point on the monitor arm, showing the Allen key inserted and directional arrows for adjusting tension for lighter or heavier screens.
Operating the Monitor Mount
The ONKRON G120-BLK offers a range of adjustments for optimal viewing kanyamanan.
- Penyesuaian Jangkungna: The arm allows for 11 inches (28 cm) of vertical height adjustment. Gently push or pull the monitor to the desired height.
- Ékstensi/Panyabutan: The arm can extend from 3.5 inches (8.9 cm) to 13.7 inches (34.8 cm) from the wall.
- Dengdekkeun: Adjust the monitor tilt from +90° to -45° to reduce glare and find your preferred viewsudut ing.
- Putar: Swivel the monitor 180° left or right.
- Rotasi: Puterkeun monitor 360° pikeun orientasi lanskap atanapi potret.
Image: Four panels demonstrating the full motion capabilities of the mount: 180° swivel, 360° rotation, +90° to -45° tilt, and 11 inches of height adjustment.
Manajemén kabel
Utilize the integrated cable management system to keep your workspace tidy.
- Route monitor cables through the channels on the underside of the arm.
- Secure the cables using the provided clips or covers to maintain a clean appearance.
Gambar: Deukeut view of the monitor arm showing a cable neatly routed through the integrated cable management channel.
Pangropéa
Pangropéa rutin mastikeun umur panjang sareng kinerja anu optimal tina dudukan monitor anjeun.
- beberesih: Ngusap gunung ku lemes, damp lawon. Hindarkeun pembersih abrasive atanapi pangleyur.
- Cék périodik: Périodik pariksa sagala screws sareng sambungan pikeun mastikeun aranjeunna tetep kedap. Re-tighten lamun perlu.
- Pangaluyuan Pegas Gas: If your monitor's weight changes or if the arm no longer holds its position, re-adjust the gas spring tension as described in the Setup section.
Pamérésan masalah
Tingal bagian ieu pikeun solusi masalah umum.
| Masalah | Mungkin Cukang lantaranana | Solusi |
|---|---|---|
| Monitor ngagantung atanapi henteu tetep dina jangkungna anu dipikahoyong. | Tegangan pegas gas handap teuing pikeun beurat monitor. | Increase gas spring tension by turning the adjustment screw clockwise with the Allen key. Refer to 'Adjusting for Monitor Weight' in the Setup section. |
| Monitor springs up or is difficult to push down. | Tegangan pegas gas teuing luhur pikeun beurat monitor. | Decrease gas spring tension by turning the adjustment screw counter-clockwise with the Allen key. Refer to 'Adjusting for Monitor Weight' in the Setup section. |
| Dudukanna karasana teu stabil atanapi oyag. | Loose connections or improper wall installation. | Check all mounting screws on the wall plate and VESA plate. Ensure they are securely tightened. Verify the wall can support the mount and monitor. |
| Difficulty with monitor movement (tilt, swivel, rotation). | Sendi-sendina pageuh teuing. | Some joints may have adjustable tension screws. Loosen slightly if movement is too stiff. Do not over-loosen. |
spésifikasi
- model: G120-BLK
- Kasaluyuan Ukuran Layar: 13 - 34 inci
- Kapasitas beurat: 2.2 - 17.6 lbs (1 - 8 kg)
- Kasaluyuan VESA: 75x75mm, 100x100mm
- Sudut Dengdekkeun: +90 ° ka -45 °
- Sudut puteran: 180°
- Rotasi: 360°
- Penyesuaian Jangkungna: 11 inci (28 cm)
- Ékstensi Leungeun: 3.5 inci (8.9 cm) nepi ka 13.7 inci (34.8 cm)
- Bahan: alumunium
- Ukuran produk: 16.34 x 2.28 x 6.61 inci (41.5 x 5.8 x 16.8 cm)
- Beurat barang: 3.96 pon (1.8 kg)
Garansi sareng Rojongan
ONKRON products are manufactured with quality and durability in mind. For specific warranty details, please refer to the warranty card included with your product or visit the official ONKRON websitus.
If you encounter any issues or have questions regarding your ONKRON G120-BLK monitor mount, please contact ONKRON customer support for assistance. Our experts are available to help.
Inpormasi kontak: Please refer to the ONKRON websitus atanapi kemasan produk kanggo kéngingkeun detil kontak anu pangénggalna.
