1. Bubuka
This manual provides detailed instructions for the proper use and maintenance of your VISEL ELIMINACODE radio remote control. This device is designed to operate seamlessly with VISEL display models TD2, TD3, TD4, MD2, and MD3, allowing for code elimination without direct interaction with the display's buttons or cables.
2. Émbaran Kasalametan
- Jauhkeun kadali jauh tina cai sareng kalembaban anu kaleuleuwihan.
- Hindarkeun ngaragragkeun alatna atanapi mangaruhan kana tabrakan anu kuat.
- Ulah nyobian muka atanapi ngalereskeun remot kontrol nyalira. Hubungi tanaga anu mumpuni pikeun diservis.
- Buang batré anu dipaké sacara tanggung jawab nurutkeun peraturan lokal.
3. Eusi Paket
Pastikeun sadaya item aya dina bungkusan:
- VISEL ELIMINACODE Remote Control
- Batré 12V (tos dipasang atanapi kalebet misah)
- Manual Pamaké ieu
4. Produk Langkungview
The VISEL ELIMINACODE remote control features a simple, ergonomic design for ease of use. Below is an illustration of the device and its key components.
Gambar 1: VISEL ELIMINACODE Remote Control. The remote is dark grey, shaped like a stylized 'V' or 'Y'. It features a large red circular button labeled "NEXT" at the top, a smaller red circular indicator labeled "C" on the left, and a small grey circular indicator on the right. The brand name "Minipoint" is visible in the center, and a small circular hole is present at the bottom center, likely for a lanyard or attachment.
- NEXT Button (Red, Large): Used to advance the display to the next code or number.
- C Button/Indicator (Red, Small): Typically used for clearing or resetting functions, or as an indicator.
- Status Indicator (Grey, Small): May indicate power, signal transmission, or other operational status.
5. Setélan
5.1. Pamasangan/Pamariksaan Batré
The remote control comes with a 12V battery included. In most cases, the battery is pre-installed. If the remote does not respond, check the battery compartment for proper installation or replace the battery.
- Teangan tempat panutup kompartemen batré dina tonggong kadali jauh.
- Buka panutupna kalawan ati-ati.
- Insert or replace the 12V battery, ensuring correct polarity (+/-).
- Tutup panutup kompartemen batré aman.
5.2. Pairing with VISEL Display (If Required)
The ELIMINACODE remote control is designed to work with VISEL display models TD2, TD3, TD4, MD2, and MD3. In most cases, the remote is pre-configured. If the remote does not control the display, follow the pairing instructions provided with your specific VISEL display model. General steps may include:
- Ensure the VISEL display is powered on.
- Access the pairing mode on your VISEL display (refer to your display's manual).
- While the display is in pairing mode, press and hold the TERAS button on the remote control for a few seconds until the display acknowledges the pairing.
- Test the remote control's functionality.
6. Parentah Operasi
The ELIMINACODE remote control provides simple, intuitive operation for your VISEL display.
6.1. Advancing the Display Code
- To advance the displayed code or number on your VISEL display, simply press the large TERAS tombol sakali.
- Each press will increment the display by one unit.
6.2. Clearing/Resetting the Display
- To clear the current code or reset the display, press the small C kancing.
- The exact function of the 'C' button may vary slightly depending on your specific VISEL display model. Refer to your display's manual for detailed information.
6.3. Operational Range
The remote control operates using a radio frequency of 433.92 MHz. Ensure there are no significant obstructions between the remote and the display for optimal performance. The effective range may vary based on environmental conditions.
7. Pangropéa
7.1. beberesih
Wipe the remote control with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these can damage the casing sareng komponén internal.
7.2. Ngagantian batré
When the remote control's range decreases or it becomes unresponsive, it is likely time to replace the 12V battery. Follow the steps in Section 5.1 for battery replacement.
7.3. Panyimpenan
Store the remote control in a cool, dry place, away from direct sunlight and extreme temperatures, when not in use for extended periods.
8. Cara ngungkulan
| Masalah | Mungkin Cukang lantaranana | Solusi |
|---|---|---|
| Jauh teu ngaréspon | Dead or improperly installed battery. Out of range. Not paired with display. | Check/replace battery. Move closer to the display. Re-pair the remote (Section 5.2). |
| Display not changing code | Remote not paired. Display issue. | Ensure remote is paired. Check the VISEL display's own manual for troubleshooting. |
| Reduced operational range | Low battery. Obstructions. Interference. | Replace battery. Ensure clear line of sight. Minimize sources of radio interference. |
9. Spésifikasi
| Fitur | Rincian |
|---|---|
| Ngaran produk | ELIMINACODE Remote Control |
| merek | VISEL |
| Nomer modél | TD3 (Compatible with TD2, TD3, TD4, MD2, MD3 displays) |
| Nomer Bagian | FL-TX |
| Ukuran (L x W x H) | 95 x 57 x 23 mm (kira-kira) |
| Beurat | 60 g (0.06 Kilogram) |
| Sasayogian tanaga | Batré 12V (kaasup) |
| Batré Rechargeable | No |
| Frékuénsi Radio | 433.92 MHz |
| Warna | kulawu |
| UPC | 637913146404 |
10. Garansi jeung Rojongan
For warranty information or technical support, please refer to the documentation provided with your original purchase or contact VISEL customer service directly. Contact details can typically be found on the manufacturer's official websitus.
