SINOTIMER MC101-611 Universal Intelligent Temperature Control Meter

1. Bubuka

The SINOTIMER MC101-611 is a universal intelligent temperature control meter designed for precise temperature and humidity management. It features a clear LCD display for process value (PV) and set value (SV), along with various output and alarm functions. This manual provides essential information for the safe and effective operation of your device.

Gambar 1.1: Hareupeun view of the MC101-611 Temperature Control Meter, showing the dual digital display and control buttons.

2. Émbaran Kasalametan

• Baca sagala parentah taliti saméméh instalasi tur operasi.
• Pastikeun catu daya voltage matches the device's requirements (85-265V AC, 50/60Hz).
• All wiring should be performed by a qualified electrician to prevent electric shock or damage to the device.
• Do not operate the device in environments with excessive moisture, dust, or corrosive gases.
• Disconnect power before performing any maintenance or wiring changes.
• Jauhkeun alat ieu tina gangguan éléktromagnétik anu kuat.

3. Fitur Produk

• Universal input for various temperature sensors (K, J, E, T, R, S, B, Pt100, Cu50).
• Dual digital display for Process Value (PV) and Set Value (SV).
• Multiple control outputs: Relay and SSR (Solid State Relay).
• Alarm functions (AL1, AL2) for high/low limits.
• PID auto-tuning function for precise control.
• Rentang suhu operasi anu lega.
• Compact and easy-to-install design.

4. Eusi Paket

• 1 x SINOTIMER MC101-611 Temperature Control Meter
• 1 x Mounting Bracket (as shown in Figure 4.1)
• 1 x Manual Pamaké (dokumén ieu)

Figure 4.1: The MC101-611 unit alongside its included mounting bracket, essential for panel installation.

5. Setélan

5.1 Pamasangan

The MC101-611 is designed for panel mounting. Cut an appropriate opening in your control panel and insert the meter. Secure it from the rear using the provided mounting bracket. Ensure a snug fit to prevent vibration.

5.2 Kabel

Refer to the wiring diagram on the side of the unit and Figure 5.1 for correct connections. Ensure all connections are secure and insulated. Incorrect wiring can damage the device or pose a safety hazard.

• Terminal 1 & 2: AC Power Supply (85-265V AC, 50/60Hz)
• Terminal 3 & 4: Main Output (OUT) - Normally Open (NO) and Normally Closed (NC) contacts for Relay output.
• Terminal 6 & 7: Alarm Output (ALM) - Relay contacts for alarm.
• Terminals 8, 9, 10: Sensor Input (RTD/TC) - Connect your temperature sensor here. Refer to the sensor's manual for correct polarity/connection type.
• Terminal 11 & 12: SSR Output - For connecting to a Solid State Relay.

Figure 5.1: Detailed wiring diagram on the side of the MC101-611, indicating connections for power, output, alarm, and sensor input.

6. Parentah Operasi

6.1 Pidangkeunview

The meter features a dual display:

• PV (Nilai Prosés): The upper red display shows the current measured temperature/humidity.
• SV (Nilai Setél): The lower green display shows the desired set point.
• Indikator OUT: Illuminates when the main output is active.
• Indikator AT: Illuminates when the auto-tuning function is active.
• AL1/AL2 Indicators: Illuminate when Alarm 1 or Alarm 2 conditions are met.

6.2 Fungsi Tombol

• Tombol SET: Dianggo pikeun asup ka modeu setélan parameter sareng mastikeun pilihan.
• < / R/S Button: Used to shift digits during setting or to reset alarms.
• ▼ (Down) Button: Decreases the value of a parameter or set point.
• ▲ (Up) Button: Increases the value of a parameter or set point.

6.3 Setting the Temperature/Humidity Set Point (SV)

1. Dina modeu operasi normal, pencét tombol SET button once. The SV display will begin to flash.
2. Ngagunakeun éta ▲ (Up) jeung ▼ (Down) buttons to adjust the SV to your desired value. Use the < / R/S button to shift the cursor for faster adjustment.
3. Pencét éta SET button again to confirm the new SV and exit the setting mode.

6.4 Setélan Parameter Lanjutan

To access advanced parameters (e.g., input type, control mode, alarm settings, PID parameters), press and hold the SET button for approximately 3-5 seconds until the first parameter code appears on the PV display. Use the ▲ (Up) jeung ▼ (Down) buttons to navigate through parameters and the SET button to enter and confirm values. Refer to the detailed parameter list in the full technical manual for specific codes and their functions.

7. Pangropéa

• beberesih: Ngusap tampilan na casing ku lawon anu lemes sareng garing. Ulah make cleaners abrasive atawa pangleyur.
• Pamariksaan: Pariksa périodik sambungan kabel pikeun looseness atanapi korosi.
• Panyimpenan: If storing the device for an extended period, ensure it is kept in a dry, dust-free environment within its specified storage temperature range.

8. Cara ngungkulan

9. Spésifikasi

Figure 9.1: Product label on the side of the MC101-611, detailing model, range, output, and power supply specifications.

10. Garansi jeung Rojongan

This product comes with a standard manufacturer's warranty. Please refer to your purchase documentation for specific warranty terms and conditions. For technical support, troubleshooting assistance, or warranty claims, please contact the SINOTIMER customer service through the retailer where the product was purchased or visit the official SINOTIMER websitus pikeun inpo kontak.