1. Bubuka
This manual provides essential instructions for the safe and effective use, installation, and maintenance of your RUPES Skorpio III Slim Backing Pad (Model 981.500). This backing pad is designed for use with random orbital sanders, featuring a 150mm (6-inch) diameter, hook and loop attachment, and multi-hole vacuum compatibility. Please read this manual thoroughly before use and retain it for future reference.
Gambar 1: RUPES Skorpio III Slim Backing Pad (Model 981.500). This image shows the top view of the backing pad, highlighting its multi-hole design for vacuum compatibility, the hook and loop surface, and the central M8 bolt attachment point.
2. Émbaran Kasalametan
Always observe general safety precautions when working with power tools and accessories. Failure to follow these instructions may result in injury or damage to the product or equipment.
- Ensure the backing pad is securely attached to the sander before operation.
- Salawasna nganggo alat pelindung diri (APD) anu merenah, kalebet pelindung panon, pelindung dédéngéan, sareng masker lebu.
- Inspect the backing pad for damage or wear before each use. Do not use a damaged pad.
- Ensure the sandpaper or abrasive disc is correctly aligned and firmly attached to the hook and loop surface.
- Do not exceed the maximum RPM rating of your sander or the backing pad.
- Tetep leungeun jeung pakean leupas tina bagian puteran.
3. Setup jeung Instalasi
Follow these steps to properly install the RUPES Skorpio III Slim Backing Pad onto your random orbital sander:
- Pegatkeun daya: Ensure your random orbital sander is disconnected from its power source (unplugged or battery removed) before attempting any installation or maintenance.
- Cabut Pad Old (upami aya): If replacing an existing backing pad, use the appropriate tool (often a wrench or hex key) to loosen and remove the central bolt securing the old pad.
- Inspect Sander Spindle: Clean any debris from the sander's spindle and ensure the threads are clear and undamaged.
- Attach New Pad: Align the central hole of the RUPES Skorpio III Slim Backing Pad with the sander's spindle. The pad includes an M8 bolt. Insert the bolt through the pad and into the sander's spindle.
- Secure Tightening: Hand-tighten the bolt first, then use a wrench to firmly secure the backing pad. Do not overtighten, as this can damage the threads or the pad. Ensure the pad is flush and does not wobble.
- Attach Abrasive: Press the desired hook and loop abrasive disc firmly onto the backing pad, ensuring it is centered and all vacuum holes are aligned (if using a multi-hole disc).
4. Parentah Operasi
Once the backing pad and abrasive are installed, you can begin operation:
- Sambungkeun Kakuatan: Reconnect your random orbital sander to its power source.
- Persiapan permukaan: Ensure the workpiece is clean and free of loose debris. Secure the workpiece to prevent movement during sanding.
- Téhnik Amplas:
- Mimitian mesin amplas sateuacan dipasangkeun kana benda kerja.
- Apply light, even pressure. Allow the sander's weight and the abrasive to do the work.
- Move the sander in overlapping passes across the surface.
- Avoid tilting the sander, which can create uneven sanding patterns or gouges.
- For optimal dust extraction, ensure your sander's vacuum system is connected and functioning.
- Ngeureunkeun Operasi: Angkat sander tina benda kerja sateuacan mareumanana.
5. Pangropéa
Regular maintenance ensures optimal performance and extends the life of your backing pad:
- beberesih: After each use, remove the abrasive disc and gently brush off any dust or debris from the hook and loop surface. A soft brush or compressed air can be used.
- Inspect Hook and Loop: Periodically check the hook and loop surface for wear. If the abrasive discs no longer adhere firmly, the pad may need replacement.
- Pariksa Karusakan: Examine the pad for cracks, tears, or excessive wear. Replace the pad immediately if any damage is observed.
- Panyimpenan: Store the backing pad in a clean, dry environment, away from direct sunlight and extreme temperatures.
6. Cara ngungkulan
If you encounter issues with your RUPES Skorpio III Slim Backing Pad, consider the following:
| Masalah | Mungkin Cukang lantaranana | Solusi |
|---|---|---|
| Abrasive disc detaches during use. | Worn hook and loop surface on the backing pad or abrasive disc. | Replace the abrasive disc. If the problem persists, replace the backing pad. |
| Excessive vibration or wobble. | Backing pad not securely tightened; damaged pad; unbalanced abrasive disc. | Ensure the pad is tightly secured. Inspect for damage and replace if necessary. Check abrasive disc for proper centering. |
| Ékstraksi lebu goréng. | Vacuum holes on abrasive disc not aligned with pad; clogged holes; vacuum system issue. | Ensure abrasive disc is correctly aligned. Clean vacuum holes on pad. Check sander's vacuum system. |
7. Spésifikasi
| Fitur | Rincian |
|---|---|
| merek | RUPES |
| Nomer modél | 981.500 |
| diaméterna | 150mm (6 inci) |
| Tipe Kantétan | Hook jeung Loop |
| Kasaluyuan vakum | Multi-Hole |
| Ukuran Bolt | M8 |
| Alat nu cocog | Acak Orbital Sander |
| Item Beurat | 10.6 ons |
| Dimensi produk | 6 "L x 6" W |
8. Émbaran jaminan
RUPES products are manufactured to high-quality standards. For specific warranty terms and conditions, please refer to the documentation included with your original sander or visit the official RUPES websitus. Simpen bukti pameseran anjeun pikeun klaim garansi.
9. Rojongan jeung Kontak
For technical assistance, spare parts, or further information regarding your RUPES Skorpio III Slim Backing Pad, please contact RUPES customer support or visit their official website. Contact details can typically be found on the RUPES packaging or their corporate websitus.
RUPES Resmi Websitus: www.rupes.com
