1. Bubuka
This manual provides essential information for the safe and effective operation of your Tektronix Digital Storage Oscilloscope, Model B07GCZSDRJ. This device is designed for precise measurement and analysis of electronic signals. Please read this manual thoroughly before using the instrument to ensure proper functionality and to prevent damage or injury.
2. Émbaran Kasalametan
Always observe the following safety precautions to prevent injury and avoid damage to this product or any products connected to it.
- Paké produk ngan sakumaha dieusian.
- Ulah make produk lamun geus ruksak.
- Perform initial safety checks before connecting to power.
- Rujuk ngalayanan ka tanaga anu mumpuni.
- Pastikeun ventilasi ditangtoskeun pikeun nyegah overheating.
- Ulah beroperasi dina baseuh atawa damp kaayaan.
3. Setélan
Follow these steps to set up your oscilloscope for the first time:
- Unpack the Instrument: Carefully remove the oscilloscope and all accessories from the packaging. Inspect for any visible damage.
- Sambungkeun Kakuatan: Connect the provided power cord to the AC input on the rear panel of the oscilloscope, then plug it into a grounded electrical outlet.
- Daya Hurung: Press the power button, usually located on the front panel. The display should illuminate.
- Kompensasi Probe: If using probes, connect a probe to Channel 1 and the probe compensation output. Adjust the probe compensation until a flat-top square wave is displayed.
This image serves as a placeholder and indicates that a specific product image is not available for display. It typically shows text like 'No image available' with a generic Amazon smile logo.
4. Parentah Operasi
This section covers basic operation of the oscilloscope.
- Kontrol Vertikal: Use the VOLTS/DIV knob to adjust the vertical scale (voltage per division) and the position knob to move the waveform vertically.
- Kontrol Horisontal: Use the SEC/DIV knob to adjust the horizontal scale (time per division) and the position knob to move the waveform horizontally.
- Sistim pemicu: The trigger controls stabilize repetitive waveforms. Adjust the trigger level and mode (e.g., Edge, Pulse) to capture the desired part of the signal.
- Fungsi pangukuran: Access built-in measurement functions (e.g., Vpp, RMS, Frequency) via the 'Measure' or 'Menu' buttons.
5. Pangropéa
Pangropéa anu leres mastikeun umur panjang sareng akurasi osiloskop anjeun.
- beberesih: Rapihkan bagian luar alat dengan lembut, damp cloth. Do not use abrasive cleaners or solvents. Ensure the instrument is powered off and unplugged before cleaning.
- Kalibrasi: Regular calibration by qualified service personnel is recommended to maintain measurement accuracy. Refer to the service manual for calibration procedures.
- Panyimpenan: When not in use, store the oscilloscope in a clean, dry environment, away from direct sunlight and extreme temperatures.
6. Cara ngungkulan
Bagian ieu nyayogikeun solusi pikeun masalah umum anu anjeun tiasa patepang.
| Masalah | Mungkin Cukang lantaranana | Solusi |
|---|---|---|
| Henteu aya tampilan saatos hurung | Power cord not connected; Power outlet fault; Internal fuse blown | Check power cord connection; Test power outlet; Contact service for fuse replacement |
| Teu aya bentuk gelombang anu ditampilkeun | Input signal too small; Probe not connected; Trigger settings incorrect | Increase VOLTS/DIV; Check probe connection; Adjust trigger level and mode |
| Waveform unstable or rolling | Trigger level incorrect; Trigger source not selected; Input signal noisy | Adjust trigger level; Select correct trigger source; Use averaging mode for noisy signals |
7. Spésifikasi
Key technical specifications for the Tektronix Digital Storage Oscilloscope, Model B07GCZSDRJ.
| Spésifikasi | Nilai |
|---|---|
| ASIN | B07GCZSDRJ |
| Produsén | Tektronix |
| Tanggal Kahiji Sadia | 11 Agustus 2018 |
8. Garansi jeung Rojongan
Tektronix products are designed for reliability and performance. This product comes with a standard manufacturer's warranty. For specific warranty terms and conditions, please refer to the documentation included with your purchase or visit the official Tektronix websitus.
For technical support, service, or to inquire about replacement parts, please contact Tektronix customer service. You can find contact information on the official Tektronix websitus atawa ngaliwatan distributor lokal Anjeun.
Catetan: Perbaikan atanapi modifikasi anu teu sah tiasa ngabatalkeun garansi anjeun.
