Marshall DSL100HR Guitar AmpManual Pamaké Kepala lifier

1. Bubuka

Thank you for choosing the Marshall DSL100HR Guitar Amplifier Head. This 100-watt all-valve amplifier head is designed to deliver a wide range of classic Marshall tones, from pristine cleans to high-gain distortion. It features two footswitchable channels, Classic Gain and Ultra Gain, each with two modes, providing four distinct sounds. Additional features include dedicated resonance control, two master volume controls, digital reverb, high and low power settings, and a Softube emulated output for direct recording or silent practice.

This manual provides essential information for the safe and effective operation of your DSL100HR amplifier. Please read it thoroughly before connecting or operating the unit.

Figure 1: Marshall DSL100HR Guitar Amplifier Head, front viewGambar ieu némbongkeun amplifier's robust construction and classic Marshall aesthetic, featuring the control panel and input jack.

2. Parentah Kasalametan

To prevent electric shock, fire, or damage to the amplifier, always observe the following safety precautions:

• Sasayogian tanaga: Nyambungkeun amplifier only to an AC power supply of the voltage specified on the rear panel. Ensure the power cable is in good condition and properly grounded.
• Ventilasi: Ulah ngahalangan liang ventilasi. Pastikeun aliran hawa anu cekap di sakitarna amplifier pikeun nyegah overheating.
• Uap: Ulah ngalaan amplifier to rain, moisture, or excessive humidity. Keep liquids away from the unit.
• Palayanan: Entong nyobian ngalayanan amplifier yourself. Refer all servicing to qualified service personnel. High voltages aya di jero amplifier, even when switched off.
• Sambungan Speaker: Sok sambungkeun teh amplifier to a suitable speaker cabinet with the correct impedance before powering on. Operating without a speaker load can damage the output transformer.
• Tube Heat: Vacuum tubes operate at high temperatures. Avoid touching them and allow sufficient cooling time after use.
• Perlindungan dédéngéan: Ieu amplifier can produce high sound pressure levels. Prolonged exposure to high volumes can cause permanent hearing damage. Use appropriate hearing protection.

3. Setélan

3.1 Ngabongkar bungkusan

Ati-ati ngaleupaskeun amplifier from its packaging. Retain all packaging materials for future transport or storage. Inspect the amplifier for any signs of damage incurred during shipping. If damage is found, contact your dealer immediately.

3.2 Connecting to a Speaker Cabinet

The DSL100HR requires connection to an external speaker cabinet. Ensure the speaker cabinet's impedance matches one of the amplifier's output jacks (16 Ohm, 8 Ohm, or 4 Ohm). Use a high-quality speaker cable (not a guitar cable) for this connection.

• For a single 16 Ohm cabinet, connect to the '16 Ohm' jack.
• For a single 8 Ohm cabinet, connect to one of the '8 Ohm' jacks.
• For two 16 Ohm cabinets, connect each to an '8 Ohm' jack.
• For a single 4 Ohm cabinet, connect to one of the '4 Ohm' jacks.
• For two 8 Ohm cabinets, connect each to a '4 Ohm' jack.

penting: Pernah beroperasi dina amplifier without a speaker load connected to the appropriate output jack.

3.3 Sambungan Daya

Connect the supplied power cable to the IEC inlet on the rear panel of the amplifier and then to a grounded mains power outlet.

3.4 Nyambungkeun gitar

Connect your guitar to the 'INPUT' jack on the front panel using a standard instrument cable.

3.5 Sambungan Saklar Suku

Connect the supplied footswitch to the 'FOOTSWITCH' jack on the rear panel. This allows remote switching between channels and reverb on/off.

4. Parentah Operasi

4.1 Powering on / Pareum

1. Ensure all volume controls are set to minimum.
2. Switch the 'POWER' switch to the ON position.
3. Wait approximately 30-60 seconds for the tubes to warm up, then switch the 'STANDBY' switch to the ON position. The amplifier ayeuna siap dianggo.
4. To power off, reverse the sequence: 'STANDBY' to OFF, then 'POWER' to OFF.

4.2 Kadali Panel hareup

The DSL100HR features a comprehensive set of controls:

• Classic Gain Channel:
  • Volume: Controls the output level of the Classic Gain channel.
  • Keuntungan: Adjusts the amount of pre-amp gain for the Classic Gain channel.
  • Clean/Crunch Switch: Selects between a clean tone and a crunchy overdrive within the Classic Gain channel.
• Ultra Gain Channel:
  • Volume: Controls the output level of the Ultra Gain channel.
  • Keuntungan: Adjusts the amount of pre-amp gain for the Ultra Gain channel, from aggressive crunch to searing lead tones.
  • OD1/OD2 Switch: Selects between two different overdrive voicings within the Ultra Gain channel.
• Equalization (Shared):
  • Treble, Tengah, Bass: Standard tone controls to shape the ampréspon frékuénsi lifier.
  • Ayana: Adds high-end sparkle and cut to the overall sound.
  • Résonansi: Adjusts the low-end response and depth of the amppangagung.
• Ngarobah nada: A push-button switch that re-configures the amplifier's EQ for a more modern, mid-scooped sound.
• Reverb: Ngontrol tingkat éfék reverb digital bawaan.
• Master Volume 1 & 2: Two independent master volume controls allow for different overall output levels, useful for solos or rhythm sections. These can be switched via the footswitch.
• Saklar Daya Tinggi/Lemah: Reduces the amplifier's output power from 100W to 50W, allowing for lower volume operation while maintaining tube tone.

4.3 Sambungan Panel Rear

• Kaluaran Speaker: Multiple jacks for connecting speaker cabinets with various impedance ratings (16 Ohm, 8 Ohm, 4 Ohm).
• FX Loop (Send/Return): Allows connection of external effects pedals or processors. The FX loop can be bypassed.
• Kaluaran Émulasi Softube: A 6.35mm jack providing a direct, cabinet-emulated signal for recording or connecting to a PA system.
• MIDI Dina: For external MIDI control of ampfungsi liifier.
• Saklar suku: Connects the supplied footswitch for remote control of channels and reverb.

5. Pangropéa

5.1 Panggantian Tabung

The DSL100HR uses 4 x ECC83 preamp tubes and 4 x EL34 power tubes. Tubes have a finite lifespan and will eventually need replacement. Symptoms of worn tubes include loss of volume, reduced tone quality, excessive noise, or intermittent operation. Tube replacement should ideally be performed by a qualified technician, as it involves working with high voltages and proper biasing of new power tubes is crucial for optimal performance and longevity.

5.2 beberesih

Ngabersihan amplifier's exterior with a soft, dry cloth. Do not use abrasive cleaners, solvents, or waxes. Ensure the amplifier is unplugged before cleaning.

5.3 Panyimpenan

Lamun teu dipaké pikeun période nambahan, nyimpen éta amplifier in a dry, temperature-controlled environment, away from direct sunlight and extreme temperatures. Using a protective cover can help prevent dust accumulation.

6. Cara ngungkulan

If you experience issues with your DSL100HR, consult the following troubleshooting guide before seeking professional service:

7. Spésifikasi

• model: M-DSL100HR-U
• Kaluaran Wattage: 100 Watt (tiasa dirobah janten 50 Watt)
• Klep: 4 x ECC83 (sateuacannaamp), 4 x EL34 (power amp)
• Saluran: 2 (Classic Gain, Ultra Gain) with 2 modes each
• Kadali: Volume, Gain (x2), Treble, Middle, Bass, Presence, Resonance, Reverb, Master Volume (x2), Tone Shift, Clean/Crunch, OD1/OD2, High/Low Power
• Input: 1 x 6.35mm Instrument Input
• Kaluaran: Speaker Outputs (1x16 Ohm, 2x8 Ohm, 2x4 Ohm), Softube Emulated Output (6.35mm)
• Loop épék: Series FX Loop (Send/Return)
• MIDI: MIDI Dina
• Saklar suku: Included (channel/reverb switching)
• Beurat barang: 48.7 pon (22.09 kg)
• Ukuran produk: 13.8 x 33.7 x 15.9 inci (35.05 x 85.6 x 40.39 cm)
• Tipe Bahan: logam
• Sumber Daya: Kabel Listrik

8. Garansi jeung Rojongan

For warranty information, technical support, or service inquiries, please refer to the warranty card included with your product or visit the official Marshall Amplifikasi websitus. Simpen bukti pameseran anjeun pikeun klaim garansi.

Marshall Amplification is committed to providing high-quality products and customer satisfaction. Should you require assistance beyond the scope of this manual, please contact authorized Marshall service centers or customer support.