1. Bubuka
The Shinko VCR-134 is a precision temperature controller designed for industrial and scientific applications requiring accurate temperature regulation. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your VCR-134 unit.
Gambar 1: Hareupeun view of the Shinko VCR-134 Temperature Controller. It features two digital displays (PV and SV), indicator lights for CON, A1, A2, HB, and AT/RST, and control buttons including up/down arrows, MODE, AT/RST, and ON/OFF.
2. Setup jeung Instalasi
2.1 Ngabongkar bungkusan
- Kaluarkeun kontroler tina bungkusna kalayan ati-ati.
- Inspect the unit for any signs of damage during transit. If damage is found, contact your supplier immediately.
- Pastikeun yén sadaya komponén anu didaptarkeun dina daptar bungkusan aya.
2.2 Pamasangan
The VCR-134 is designed for panel mounting. Ensure the mounting location provides adequate ventilation and is free from excessive vibration, dust, moisture, and corrosive gases. Refer to the product's dimensional drawings for precise cutout requirements.
2.3 Kabel
All wiring should be performed by a qualified electrician in accordance with local and national electrical codes. Ensure the power supply is disconnected before making any connections. Connect the power supply, sensor input, and control outputs to the designated terminals on the rear of the unit. Refer to the wiring diagram provided with your specific model for detailed instructions.
3. Operasi
3.1 Panel hareup Leuwihview
- tampilan PV: Shows the Process Value, which is the current measured temperature.
- tampilan SV: Shows the Set Value, which is the target temperature.
- CON Indicator: Nyaangan nalika kaluaran kontrol aktip.
- A1/A2 Indicators: Alarm indicators, illuminating when respective alarm conditions are met.
- HB Indicator: Heater Break alarm indicator.
- AT/RST Indicator: Auto-tuning or Reset indicator.
- Tombol Naék / Turun: Used to adjust set values and navigate menus.
- Tombol MODE: Used to cycle through different operating modes and parameter settings.
- AT/RST Button: Initiates auto-tuning or resets alarms/functions.
- Tombol ON/OFF: Ngahurungkeun atanapi mareuman unit.
3.2 Operasi Dasar
- Daya Hurung: Pencét éta ON/OFF button to power on the controller. The PV and SV displays will illuminate.
- Setting the Temperature (SV):
- Ensure the controller is in its normal operating mode.
- Ngagunakeun éta Up or Turun arrow buttons to adjust the SV (Set Value) to your desired temperature. The SV display will flash during adjustment.
- The new SV will be automatically saved after a few seconds of inactivity or by pressing the MODÉ kancing.
- Suhu pangimeutan: The PV display continuously shows the current measured temperature.
- Pareum listrik: Pencét éta ON/OFF button again to power off the controller.
4. Pangropéa
4.1 beberesih
To maintain optimal performance and appearance, clean the controller's front panel periodically. Use a soft, dry cloth. For stubborn dirt, a cloth lightly dampened with a mild, non-abrasive cleaner may be used. Avoid using strong solvents or abrasive materials, as these can damage the display and casing.
4.2 Kalibrasi
The Shinko VCR-134 is factory calibrated for accuracy. If recalibration is suspected to be necessary due to prolonged use or environmental changes, it should be performed by qualified personnel using appropriate calibration equipment. Refer to the detailed service manual for calibration procedures, or contact Shinko technical support.
5. Cara ngungkulan
This section provides solutions to common issues encountered during the operation of the VCR-134. If the problem persists after attempting these solutions, contact technical support.
| Masalah | Mungkin Cukang lantaranana | Solusi |
|---|---|---|
| Henteu aya kakuatan pikeun unit | Power cable disconnected; Blown fuse; No power from source. | Check power cable connection; Inspect and replace fuse if necessary; Verify power supply. |
| Layar PV némbongkeun 'HHHH' atawa 'LLLL' | Sensor open circuit (HHHH); Sensor short circuit or reverse connection (LLLL). | Check sensor wiring and connections; Replace faulty sensor. |
| Maca suhu teu akurat | Incorrect sensor type selected; Sensor damaged; Environmental interference. | Verify sensor type setting; Inspect sensor; Shield sensor wiring from electrical noise. |
| Controller not responding to button presses | Unit frozen; Keypad malfunction. | Power cycle the unit; If issue persists, contact support. |
6. Spésifikasi
The following are key technical specifications for the Shinko VCR-134 Temperature Controller:
| Fitur | Rincian |
|---|---|
| Produsén | Shinko |
| Modél | VCR-134 |
| Warna | Hideung |
| Tipe tampilan | LCD or LED (Digital) |
| Temperature Range (Example) | 0 ~ 400°C (K-type thermocouple) |
7. Garansi jeung Rojongan
7.1 Émbaran jaminan
Shinko products are manufactured to high quality standards and are typically covered by a limited warranty against defects in materials and workmanship. Please refer to the warranty card included with your product or visit the official Shinko website for specific warranty terms and conditions applicable to the VCR-134.
7.2 Rojongan Téknis
For technical assistance, troubleshooting beyond this manual, or service inquiries, please contact your authorized Shinko distributor or visit the official Shinko website for contact information. When contacting support, please have your product model number (VCR-134) and any relevant error messages or symptoms ready.
