Stihl MS 201 TC-M Chainsaw Instruction Manual

1. Émbaran Kasalametan

Operating a chainsaw can be dangerous if proper safety precautions are not followed. Always read and understand the entire instruction manual before operating the Stihl MS 201 TC-M chainsaw. Failure to follow safety instructions can result in serious injury or death.

Alat Pelindung Diri (APD)

• Perlindungan sirah: Wear a safety helmet with face and hearing protection.
• Perlindungan panon: Salawasna make kacamata kaamanan atawa kacasoca.
• Perlindungan leungeun: Anggo sarung tangan tugas beurat.
• Perlindungan suku: Ngagem calana panjang pelindung chainsaw atanapi chaps.
• Perlindungan suku: Wear safety boots with steel toes and non-slip soles.

Fuel Handling Safety

• Always mix and handle fuel in a well-ventilated area, away from ignition sources.
• Paké ngan disatujuan wadahna suluh.
• Entong ngaroko bari ngala suluh.
• Langsung usap suluh nu tumpah.

2. Produk Langkungview

The Stihl MS 201 TC-M is a powerful and compact gasoline-powered chainsaw designed for professional tree care and pruning. It features a 35 cm cutting length and is equipped with advanced engine technology for efficient operation.

Gambar 2.1: Sisi luhur view of the Stihl MS 201 TC-M chainsaw, highlighting the ergonomic handle and engine housing.

Gambar 2.2: Sisi view of the Stihl MS 201 TC-M chainsaw, showing the Stihl branding and engine components.

3. Setélan

Unpacking jeung Majelis

1. Sacara saksama miceun sadaya komponén tina bungkusan.
2. Inspect for any shipping damage. If damaged, do not use and contact your dealer.
3. Pastikeun sadaya bagian anu didaptarkeun dina daptar bungkusan aya.

Bar and Chain Installation

Proper installation of the guide bar and saw chain is crucial for safe and efficient operation.

1. Pastikeun rem ranté geus dicabut.
2. Remove the chain sprocket cover by loosening the nuts.
3. Place the guide bar onto the studs.
4. Fit the saw chain around the sprocket and into the guide bar groove. Ensure the cutting edges face forward on the top of the bar.
5. Replace the chain sprocket cover and hand-tighten the nuts. Do not fully tighten yet.
6. Adjust chain tension (refer to 'Chain Tension Adjustment' in Section 5).
7. Fully tighten the chain sprocket cover nuts.

angka 3.1: Tutup-up view of the chainsaw's chain and guide bar, illustrating proper assembly.

Fuel and Chain Oil Filling

The MS 201 TC-M operates on a gasoline-oil mixture and requires chain lubricant.

• BBM: Use a high-quality unleaded gasoline mixed with Stihl 2-stroke engine oil at the recommended ratio (typically 50:1). Refer to the fuel tank cap for specific ratios.
• Minyak ranté: Fill the chain oil tank with high-quality bar and chain lubricant. Do not use waste oil.

Ensure both caps are securely tightened after filling.

4. Parentah Operasi

Ngamimitian Chainsaw

1. Tempatkeun gergaji mesin dina permukaan anu teuas sareng rata.
2. Aktipkeun rem ranté ku cara ngadorong pelindung leungeun hareup ka hareup.
3. Set the master control lever to the cold start position (choke).
4. Cekel gergaji mesin pageuh ku hiji leungeun dina gagang hareup teras tempatkeun suku anjeun dina gagang tukang.
5. Pull the starter cord slowly until resistance is felt, then pull briskly until the engine fires briefly.
6. Move the master control lever to the half-throttle position.
7. Tarik deui kabel starter nepi ka mesin hurung.
8. Blip the throttle to disengage the half-throttle and return to idle.
9. Cabut rem ranté sateuacan ngamimitian operasi motong.

Ngeureunkeun Gergaji Mesin

To stop the engine, move the master control lever to the STOP position.

Operasi marake ranté

The chain brake is a critical safety feature. It can be engaged manually by pushing the front hand guard forward or automatically by inertia during kickback. Always ensure the chain brake is functional before each use.

5. Pangropéa

Regular maintenance ensures the longevity and safe operation of your Stihl MS 201 TC-M chainsaw.

Ranté adjustment tegangan

Correct chain tension is vital. A loose chain can derail, and an overly tight chain can cause premature wear to the bar and chain, and reduce engine power.

1. Loosen the nuts on the chain sprocket cover.
2. Using the tensioning screw, adjust the chain until it fits snugly against the underside of the guide bar, but can still be pulled around by hand.
3. Lift the tip of the guide bar slightly while tightening the nuts on the chain sprocket cover.
4. Check tension again.

Asah ranté

A sharp chain is essential for efficient and safe cutting. Sharpen the chain regularly or have it professionally sharpened.

Filter hawa beberesih

Clean the air filter regularly to maintain engine performance and prevent damage. Remove the filter cover and clean the filter element with warm soapy water or compressed air. Replace if damaged.

Inspeksi Spark Plug

Inspect the spark plug for wear and proper gap. Replace if electrodes are worn or fouled. Refer to the specifications for the correct spark plug type and gap.

Guide Bar Pangropéa

Regularly clean the guide bar groove and oil holes. Flip the guide bar periodically to ensure even wear.

6. Cara ngungkulan

This section addresses common issues you might encounter with your Stihl MS 201 TC-M chainsaw.

7. Spésifikasi

Key technical specifications for the Stihl MS 201 TC-M chainsaw:

• Jumlah modél: MS 201
• Sumber Daya: Bensin
• Panjang motong: 35 cm
• Beurat barang: 3.85 kg (8.49 lbs)
• Ukuran produk: 37 x 10 x 37 cm (14.57 x 3.94 x 14.57 inci)
• Bahan: Plastik (perumahan)
• Pabrikan: STIHL
• GTIN (UPC): 00795711953546

8. Garansi jeung Rojongan

For warranty information, please refer to the warranty card included with your product or contact your authorized Stihl dealer. Keep your proof of purchase for warranty claims.

For technical support, spare parts, or service, please contact your local authorized Stihl service center. Only use genuine Stihl replacement parts and accessories.