Hyundai HY6000 Gasoline Generator User Manual

3.1 Ngabongkar sareng Inspeksi

Carefully remove the generator from its packaging. Inspect for any damage that may have occurred during shipping. If any damage is found, contact your dealer immediately.

3.2 Nempatkeun

Place the generator on a firm, level surface. Ensure there is adequate clearance around the unit for proper ventilation and to prevent heat buildup. Keep it at least 1 meter (3 feet) away from buildings or other equipment.

3.3 Nambahkeun Oli Mesin

The generator is shipped without engine oil. Before first use, add the recommended engine oil (e.g., SAE 10W-30) to the crankcase. Refer to the oil fill cap or dipstick for the correct level. Do not overfill.

Gambar 1: Samping view of the generator engine. The oil fill cap is typically located on the side of the engine block, often yellow or black, and may have a dipstick attached for checking oil level.

3.4 Nambahan Suluh

Use fresh, unleaded gasoline with an octane rating of 87 or higher. Fill the fuel tank carefully, avoiding spills. Do not fill above the red indicator or the bottom of the filler neck. Securely close the fuel cap after filling.

• Always refuel in a well-ventilated outdoor area.
• Pastikeun mesin pareum sareng tiis sateuacan ngeusian bengsin.
• Do not smoke or use open flames near the generator.

3.5 Ngagroundkeun Generator

For safety, the generator must be properly grounded. Connect a heavy-gauge copper wire from the generator's grounding terminal to an earth ground rod or other approved grounding source. Consult local electrical codes for specific requirements.

4.1 Control Panel Leuwihview

Gambar 2: Hareupeun view of the control panel. Features include two 16A AC outlets, a digital LED display for voltage/frequency/hours, a circuit breaker, and a DC 12V output with thermal protection.

Panel kontrol ngawengku:

• AC Outlets (2x 16A): For connecting 220V appliances. Equipped with overload protection.
• Tampilan LED Digital: Nembongkeun voltage, frékuénsi, jeung jam operasi.
• Pamutus Sirkuit: Protects against overloads.
• DC 12V Output (8.3A): For charging 12V batteries, with thermal protection.
• Terminal handap: For connecting to an earth ground.
• Indikator LED: For overload or usage status.

4.2 Starting the Engine (Manual Start)

1. Pastikeun generator aya dina permukaan anu rata sareng di-ground kalayan leres.
2. Pariksa tingkat oli mesin sareng bahan bakar.
3. Hurungkeun klep suluh ka posisi "ON".
4. Pindahkeun uas cuk ka posisi "CHOKE" (lamun mesin geus tiis).
5. Hurungkeun saklar mesin ka posisi "ON".
6. Grasp the recoil starter handle firmly and pull it slowly until resistance is felt, then pull quickly and smoothly to start the engine.
7. Sakali mesin dimimitian, lalaunan pindahkeun uas cuk ka posisi "RUN".
8. Keun mesin panasan heula sababaraha menit sateuacan nyambungkeun beban listrik.

Gambar 3: Samping view of the generator, highlighting the manual recoil pull start handle, typically yellow or black, located on the engine's flywheel cover.

4.3 Nyambungkeun Beban Listrik

After the engine has warmed up, you can connect your appliances. Ensure the total wattage of connected devices does not exceed the generator's rated output (4400W). Overloading the generator will trip the circuit breaker.

• Plug appliances directly into the AC outlets on the control panel.
• For 12V DC charging, connect the appropriate cables to the DC output.
• If the generator stops due to overload, reduce the load and reset the circuit breaker.

4.4 Ngeureunkeun Mesin

1. Pegatkeun sambungan sadaya beban listrik tina generator.
2. Hurungkeun saklar mesin ka posisi "OFF".
3. Hurungkeun klep suluh ka posisi "OFF".

5.1 Jadwal pangropéa

5.2 Robah Oli Mesin

Drain the old oil while the engine is warm. Remove the oil drain plug and allow all oil to drain into a suitable container. Replace the drain plug and refill with the recommended amount and type of new engine oil.

5.3 Filter hawa beberesih

Remove the air filter cover and take out the foam filter element. Wash it in warm, soapy water, rinse thoroughly, and allow it to dry completely. Lightly oil the foam element with engine oil, squeeze out excess, and reinstall.

5.4 Inspeksi Spark Plug

Remove the spark plug and inspect its condition. Clean any carbon deposits with a wire brush. Check the gap with a feeler gauge and adjust if necessary. Replace if the electrode is worn or damaged.

5.5 Panyimpenan

For long-term storage, drain the fuel tank and carburetor, or add a fuel stabilizer. Change the engine oil. Clean the generator thoroughly. Store in a clean, dry, well-ventilated area.