Pisau Styrofoam Listrik Genggam Hercules SC-190 Pitunjuk Manual

1. Bubuka

The Hercules SC-190 is a versatile 190/200 watt electric hot knife designed for smooth and efficient cutting of various foam materials. This manual provides essential information for safe and effective operation, setup, maintenance, and troubleshooting of your hot knife.

2. Parentah Kasalametan

WARNING: Always read and understand all safety instructions before operating this tool.

• Use in a well-ventilated area to avoid inhaling fumes produced during cutting.
• Anggo alat pelindung pribadi anu pas, kalebet kacamata sareng sarung tangan.
• Keep the hot knife away from flammable materials.
• Do not touch the blade when hot. Allow it to cool completely before handling or storing.
• Always unplug the tool when not in use, before changing blades, or performing maintenance.
• Jauhkeun barudak sareng jalma anu aya di tempat operasi.
• Entong nganggo alat upami kabel listrik rusak.
• Use only Hercules-approved blades and accessories.
• Avoid continuous operation for extended periods. Allow the tool to cool down periodically to prevent overheating.

3. Eusi Paket

Your Hercules SC-190 kit includes the following items:

• Hercules SC-190 Hot Knife Unit
• 4" (10 cm) Flat Blade
• 6" (15 cm) Flat Blade
• Heavy-Duty Molded Plastic Case
• Hex Wrench (Allen Wrench)
• Sikat beberesih
• Instruksi Manual

4. Setélan

4.1 Ngagantelkeun agul

1. Ensure the hot knife is unplugged and completely cool.
2. Using the provided hex wrench, loosen the two holding screws on the blade holder at the front of the tool.
3. Carefully insert the desired blade (4" or 6") into the slots of the blade holder. Ensure the blade is fully seated.
4. Tighten the holding screws firmly with the hex wrench to secure the blade. Ensure a good electrical contact.

4.2 Sambungan Daya

Plug the power cord into a standard 120V AC outlet. The tool is now ready for operation.

5. Parentah Operasi

5.1 Kontrol Suhu

The SC-190 features a 15-level temperature control knob on the handle. Rotate the knob to adjust the heat output according to the material being cut. Lower settings are suitable for thinner or less dense foams, while higher settings are for thicker or denser materials.

5.2 Prosedur motong

1. Place the material to be cut on a stable, heat-resistant surface.
2. Select the appropriate temperature setting. It is recommended to start with a lower setting and increase if necessary.
3. Press the spring-loaded trigger to activate the heating element. The blade will heat up rapidly (within seconds).
4. Once the blade is hot, gently press it against the material along your desired cutting line. The hot knife should glide through the material with minimal resistance.
5. Maintain a steady, even pressure and speed for a clean cut. Avoid forcing the blade, as this can lead to uneven cuts or damage to the blade.
6. Release the trigger when the cut is complete or if the blade starts to smoke excessively.
7. For continuous cutting, you may need to periodically release and press the trigger to maintain optimal blade temperature.

5.3 Bahan anu Cocog

The SC-190 is suitable for cutting lightweight foam, KT board, pink foam, polyurethane, polyethylene, expanded polystyrene (EPS), extruded polystyrene (XPS), styrofoam, polyester foam, sponge, rubber, and other similar materials.

5.4 Official Product Video: Hercules SC-190 Styrofoam Hotknife

6. Pangropéa

6.1 Ngabersihkeun Bilah

After each use, allow the blade to cool slightly but remain warm. Use the provided cleaning brush to gently remove any melted foam residue from the blade. For stubborn residue, a small amount of rubbing alcohol on a cloth can be used once the blade is completely cool and unplugged.

6.2 Panyimpenan

Always store the hot knife and its accessories in the heavy-duty molded plastic case when not in use. Ensure the blade is cool and properly secured or removed before storage.

7. Cara ngungkulan

• Blade not heating: Check if the power cord is securely plugged in. Ensure the blade is properly installed and the holding screws are tightened to ensure good electrical contact. Verify the temperature control knob is not set to the lowest (off) position.
• Poor cut quality: Adjust the temperature setting. Too low a temperature may result in tearing, while too high may cause excessive melting and fumes. Ensure the blade is clean and free of residue. Adjust cutting speed and pressure.
• Excessive smoke/fumes: Reduce the temperature setting. Ensure adequate ventilation. This indicates the material is burning rather than melting cleanly.

8. Spésifikasi

9. Garansi jeung Rojongan

The Hercules SC-190 Hot Knife comes with a garansi 1 taun. For warranty claims, technical support, or replacement parts, please contact Universal Sewing Supply, the vendor, through their Amazon store or official websitus.

Vendor: Universal Sewing Supply

Toko Amazon: Hercules Cutters Store