Bubuka
This manual provides detailed instructions for the proper installation, operation, and maintenance of your NISSAN Genuine Wiper Pivot Assembly, model B8860-D4000. Please read this manual thoroughly before beginning any work to ensure safe and correct usage and to maximize the lifespan of the component.
Émbaran Kasalametan
Utamakeun kasalametan nalika ngerjakeun kendaraan anjeun. Gagal nuturkeun pedoman kaamanan ieu tiasa nyababkeun cilaka atanapi karusakan kana kendaraan.
- Anggo alat pelindung pribadi (PPE), sapertos kacamata kaamanan sareng sarung tangan.
- Ensure the vehicle is turned off, the ignition key is removed, and the parking brake is engaged before starting any installation.
- Upami anjeun henteu yakin kana léngkah naon waé, konsultasi ka teknisi otomotif anu mumpuni.
- Jauhkeun barudak jeung piaraan ti wewengkon gawé.
Eusi pakét
Pariksa yén sadaya komponén aya sateuacan ngamimitian pamasangan:
- 1 x NISSAN Genuine Wiper Pivot Assembly (Model B8860-D4000)
- (Additional fasteners or seals may be included depending on the specific kit)
Image: NISSAN Genuine Wiper Pivot Assembly, Model B8860-D4000. This image shows the complete wiper pivot assembly, including the main pivot mechanism and mounting points.
Pamasangan
This section outlines the general steps for installing the wiper pivot assembly. Specific procedures may vary slightly depending on your vehicle model. Refer to your vehicle's service manual for detailed instructions.
- Persiapan: Park the vehicle on a level surface, engage the parking brake, and turn off the engine. Disconnect the negative terminal of the battery to prevent electrical hazards.
- Access the Wiper Mechanism: Depending on your vehicle, you may need to remove the wiper arms, cowl panel, or other trim pieces to gain access to the wiper motor and linkage assembly.
- Remove Old Pivot Assembly: Carefully disconnect any electrical connectors and remove the mounting bolts or nuts securing the old wiper pivot assembly. Note the orientation of all components for reassembly.
- Install New Pivot Assembly: Position the new NISSAN Genuine Wiper Pivot Assembly (B8860-D4000) in place. Secure it with the appropriate mounting hardware, tightening to the manufacturer's specified torque values.
- Sambungkeun deui komponén: Reconnect any electrical connectors. Reinstall the cowl panel, wiper arms, and any other trim pieces removed earlier. Ensure wiper arms are correctly positioned on the windshield.
- Fungsi Uji: Reconnect the battery. Turn on the ignition and test the wiper system to ensure smooth and proper operation across the full range of motion. Check for any unusual noises or binding.
Parentah Operasi
The NISSAN Genuine Wiper Pivot Assembly is a mechanical component that facilitates the movement of your vehicle's windshield wipers. Its operation is controlled by the vehicle's wiper motor and stalk switch.
- Ensure wiper blades are in good condition for optimal performance.
- Do not operate wipers on a dry windshield to prevent damage to the blades and pivot mechanism.
- In freezing conditions, ensure wiper blades are not frozen to the windshield before operation.
Pangropéa
Regular maintenance helps ensure the longevity and proper function of your wiper system.
- Pamariksaan: Periodically inspect the wiper pivot assembly for any signs of wear, corrosion, or loose connections.
- beberesih: Keep the area around the wiper pivots clean from debris, leaves, and dirt that could impede movement.
- Lubrication: While the pivot assembly is typically sealed and pre-lubricated, if excessive squeaking or stiffness occurs, consult a professional for appropriate lubrication methods. Avoid applying lubricants that may attract dirt.
- Wiper Blades: Replace wiper blades regularly (typically every 6-12 months) or when they show signs of streaking or chattering. Worn blades can put undue stress on the pivot mechanism.
Pamérésan masalah
| Masalah | Mungkin Cukang lantaranana | Solusi |
|---|---|---|
| Wipers not moving or moving slowly | Blown fuse, faulty wiper motor, seized pivot assembly, loose electrical connection. | Check fuse. Inspect wiper motor. If pivot is seized, replacement may be necessary. Check and secure electrical connections. |
| Wipers making excessive noise (squeaking/grinding) | Worn wiper blades, lack of lubrication in pivot, debris in mechanism. | Replace wiper blades. Clean debris from pivot area. Consult a technician for pivot lubrication if needed. |
| Wipers not clearing windshield effectively | Worn wiper blades, bent wiper arm, incorrect wiper arm tension, pivot assembly issues. | Replace wiper blades. Inspect wiper arms for damage. Check wiper arm tension. If pivot is loose, replacement may be required. |
spésifikasi
- Jumlah modél: B8860-D4000
- Nomer Bagian Pabrikan: B8860-D4000
- Nomer Bagian OEM: B8860-D4000
- merek: NISSAN
- Beurat barang: 4.41 pon
- Ukuran Paket: 17.72 x 13.78 x 9.84 inci
Garansi sareng Rojongan
This NISSAN Genuine part is covered by the standard NISSAN parts warranty. For specific warranty terms and conditions, please refer to your purchase documentation or contact your authorized NISSAN dealer. For technical support or further assistance, please contact NISSAN customer service or visit the official NISSAN websitus.
NISSAN Official Websitus: www.nissanusa.com