1. Bubuka
This manual provides essential information for the safe and efficient installation, operation, and maintenance of your V-TAC VT-1277 Nano-Plastic LED Tube. Please read these instructions carefully before installation and retain them for future reference.
The V-TAC VT-1277 is an 18W T8 LED tube with a G13 fitting, measuring 120 cm in length. It features a frosted plastic cover and delivers a luminous flux of up to 1700 lumens. Constructed from nano-plastic, this tube is lightweight and designed to optimize light output while maintaining its conductive properties. It offers an efficiency of up to 94 lumens per watt and provides instant brightness without a warm-up period.
Figure 1: V-TAC VT-1277 Nano-Plastic LED Tube. This image displays the full length of the LED tube, showing its frosted white casing and the G13 base with two pins at one end.
2. Émbaran Kasalametan
- Salawasna pegatkeun sambungan kakuatan saméméh instalasi, perawatan, atawa beberesih.
- Installation should be performed by a qualified electrician if rewiring is required.
- Do not use the product in environments exceeding its IP20 rating (e.g., wet or damp lokasi).
- Pastikeun voltage supply (240V) matches the product's requirements.
- Do not attempt to modify or disassemble the LED tube.
- Buang produk ieu numutkeun peraturan lokal nalika umurna geus anggeus.
3. Eusi Paket
- 1x V-TAC VT-1277 Nano-Plastic LED Tube (18W T8 G13 120CM)
- 1x LED Starter (for electromechanical ballast replacement)
4. Spésifikasi
| Modél | VT-1277 |
| merek | V-TAC |
| Jinis Cahaya | LED |
| Wattage | 18 Watt |
| Daya Pijer Sarua | 36 Watt |
| Lamp Ukuran | T8 |
| Lamp Dasar | G13 |
| Fluks Luminous | Nepi ka 1700 lm |
| Warna Cahaya | Cold White (6400K) |
| Sudut Beam | 160° |
| Voltage | 240 volt |
| Bahan | Nano-Plastic (Frosted Cover) |
| Ukuran (L x W x H) | 125.5 x 3 x 3 cm |
| Beurat | 122.47 g |
| Peunteun IP | IP20 |
| Sertifikasi | RoHS |
5. Pamasangan
penting: Always ensure the power supply to the fixture is disconnected before beginning installation. Identify the power input side of the LED tube, which is marked with a special marker on the terminal. The short-circuit side is marked with "DO NOT connect".
5.1. Installation in LED-Ready Fixtures (Direct Mains Connection)
- Ensure the fixture is designed for direct mains connection LED tubes.
- Insert the LED tube into the G13 lampholders, ensuring the power input side aligns with the live connection and the "DO NOT connect" side aligns with the neutral connection.
- Restore power and test the LED tube.
5.2. Replacement in Fluorescent Fixtures with Electromechanical Ballast (Magnetic Ballast)
This method requires replacing the existing starter with the LED starter provided.
- Disconnect power to the fixture at the main circuit breaker.
- Leupaskeun tube fluoresensi aya ti fixture nu.
- Remove the existing starter from the fixture.
- Insert the provided LED starter into the starter socket.
- Insert the V-TAC VT-1277 LED tube into the G13 lampholders. Ensure the power input side is correctly oriented according to the fixture's wiring.
- Restore power and test the LED tube.
5.3. Replacement in Fluorescent Fixtures with Electronic Ballast
Awas: This type of installation requires modification of the fixture's internal wiring to bypass the electronic ballast. This procedure should only be performed by a tukang listrik mumpuni pikeun mastikeun kasalametan sareng fungsionalitas anu leres.
- Disconnect power to the fixture at the main circuit breaker.
- Remove the existing fluorescent tube and electronic ballast.
- Rewire the fixture to provide direct mains voltage (240V) to the G13 lampholders. Ensure that the live wire connects to the power input side of the LED tube and the neutral wire connects to the other side (marked "DO NOT connect").
- Insert the V-TAC VT-1277 LED tube into the G13 lampPanyekel.
- Restore power and test the LED tube.
6. Operasi
Once correctly installed and powered, the V-TAC VT-1277 LED tube will illuminate instantly when the fixture's power switch is turned on. There is no warm-up period required.
7. Pangropéa
- beberesih: Pegatkeun sambungan kakuatan saméméh beberesih. Make lemes, garing, atawa rada damp cloth to wipe the surface of the LED tube. Do not use abrasive cleaners or solvents.
- Pamariksaan: Periodically check the tube and connections for any signs of damage or loose connections.
- No user-serviceable parts are inside the LED tube.
8. Cara ngungkulan
8.1. LED Tube Does Not Light Up
- Pariksa Power Supply: Ensure the fixture is receiving power and the switch is in the 'ON' position.
- Pariksa Pamasangan: Verify that the LED tube is correctly seated in the lampholders and that the power input side is correctly aligned.
- Check Starter (for electromechanical ballast fixtures): Ensure the provided LED starter is correctly installed and functioning.
- Check Wiring (for electronic ballast fixtures): If the fixture was rewired, ensure the wiring was done correctly by a qualified electrician.
- Pariksa Karusakan: Check the LED tube for any visible damage. If damaged, do not use.
9. Garansi jeung Rojongan
For warranty information or technical support, please contact your V-TAC retailer or visit the official V-TAC websitus. Simpen resi pameseran anjeun salaku bukti pameseran.
