Keithley 2303-PJ Power Supply Instruction Manual
Model: 2303-PJ
1. Produk Langkungview
The Keithley 2303-PJ is a specialized power supply designed for testing portable, battery-operated devices. It offers advanced capabilities to simulate a battery's performance across a wide range of conditions, including output resistance and voltage response. This instrument is crucial for accurately testing device charge control circuitry and overall battery simulation.
fitur konci ngawengku:
- Ultra-fast response to transient load currents
- Variable output resistance
- 100nA DC current sensitivity
Figure 1: Front panel of the Keithley 2303-PJ Power Supply. The display shows voltage and current readings (e.g., 3.60V, 1.08A). Controls include a navigation pad, 'DISPLAY', 'MENU', 'OPERATE', 'ENTER', 'SET' buttons, and a 'POWER' button with indicator lights.
2. Setélan
- Ngabongkar sareng Inspeksi: Carefully remove the instrument from its packaging. Inspect for any signs of damage during transit. Report any damage to the shipping carrier and Keithley immediately.
- Sambungan Daya: Connect the supplied AC power cord to the instrument's rear panel power inlet and then to a grounded AC power outlet. Ensure the power source matches the instrument's voltage syarat.
- Daya mimiti Hurung: Pencét éta POWER button located on the front panel. The display should illuminate, indicating the unit is operational.
- Connecting to Device Under Test (DUT): Use appropriate test leads to connect the output terminals of the 2303-PJ to the device you intend to test. Observe correct polarity.
- Ventilasi: Ensure adequate ventilation around the instrument. Do not block the ventilation grilles on the sides or rear of the unit.
3. Parentah Operasi
3.1 Kadali Panel hareup
- tampilan: Némbongkeun volum kaluarantage, current, and other operational parameters.
- Tombol Navigasi (Luhur, Handap, Kénca, Katuhu): Dianggo pikeun napigasi dina ménu sareng nyaluyukeun nilai parameter.
- Tombol ENTER: Confirms selections or entered values.
- Tombol SET: Asupkeun mode setelan parameter.
- Tombol MENU: Accesses the main menu for configuration and advanced settings.
- OPERATE Button: Toggles the output on or off.
- Tombol TAMPILAN: Cycles through different display modes or views.
3.2 Operasi Dasar
- Setélan Voltage jeung Ayeuna:
- Pencét éta SET kancing.
- Use the navigation buttons to select the voltage or current parameter you wish to adjust.
- Use the navigation buttons (typically Up/Down) to change the value.
- Pencét Asupkeun pikeun mastikeun setelan.
- Enabling Output:
- Once parameters are set, press the BEROPERASI button to enable the power output. The output indicator should illuminate.
- To disable the output, press BEROPERASI deui.
- Ngawaskeun bacaan:
The display continuously shows the actual output voltage and current. Use the TAMPILAN button to cycle through different measurement views upami sayogi.
4. Pangropéa
- beberesih: Keep the instrument clean by wiping the exterior with a soft, damp cloth. Do not use abrasive cleaners or solvents. Ensure the unit is powered off and disconnected from the AC supply before cleaning.
- Ventilasi: Periodically check that the ventilation grilles are free from dust and debris to ensure proper airflow and prevent overheating.
- Panyimpenan: When not in use for extended periods, store the instrument in a clean, dry environment within its specified operating temperature and humidity ranges.
- Kalibrasi: For optimal performance and accuracy, periodic calibration by qualified personnel is recommended. Refer to the Keithley service manual or contact Keithley support for calibration procedures and intervals.
5. Cara ngungkulan
| Masalah | Mungkin Cukang lantaranana | Solusi |
|---|---|---|
| Alatna teu bisa dihurungkeun. | No AC power; faulty power cord; internal fuse blown. | Check AC power connection and outlet. Try a different power cord. If fuse is suspected, contact qualified service personnel. |
| Teu aya kaluaran voltage/ayeuna. | Output disabled; incorrect settings; overload protection active; faulty connections. | Pencét BEROPERASI to enable output. Verify voltage/current settings. Check for short circuits or overloads on the DUT. Ensure test leads are securely connected. |
| Bacaan anu teu stabil atanapi teu akurat. | Poor connections; external interference; instrument needs calibration. | Check all connections for looseness or corrosion. Ensure the instrument is away from strong electromagnetic fields. Consider professional calibration. |
| Overheating. | Blocked ventilation; excessive ambient temperature; continuous operation at maximum load. | Ensure ventilation grilles are clear. Operate in a cooler environment. Reduce load or allow for cool-down periods. |
For issues not listed here or if troubleshooting steps do not resolve the problem, please contact Keithley technical support.
6. Spésifikasi
| Parameter | Nilai |
|---|---|
| Produsén | Keithley |
| Nomer Bagian | 2303-PJ |
| Nomer Modél Item | 2303-PJ |
| Item Beurat | 5.44 kg |
| Ukuran Paket | 48.26 x 33.02 x 22.86 cm |
| Item Paket Kuantitas | 1 |
| Batré Diperlukeun? | No |
| Tanggal Kahiji Sadia | 4 Novémber 2016 |
7. Garansi jeung Rojongan
Warranty information for the Keithley 2303-PJ Power Supply is typically provided with the product at the time of purchase or can be found on the official Keithley websitus. Punten tahan bukti pameseran anjeun pikeun klaim garansi.
For technical support, service, or calibration inquiries, please contact Keithley customer service directly. Refer to the contact information provided in your product documentation or on the official Keithley websitus (www.tek.com/keithley).
