AUTONICS TC4Y-14R PID Suhu Controller Manual Pamaké

1. Bubuka

This manual provides comprehensive instructions for the installation, operation, and maintenance of the AUTONICS TC4Y-14R PID Temperature Controller. This device is designed for precise temperature control applications, featuring both Relay and SSR control outputs and operating within a 100-240VAC power supply range.

2. Émbaran Kasalametan

Please read this section carefully before installing or operating the device to ensure safe and correct usage.

Ensure power is disconnected before performing any wiring or maintenance.
This device should only be installed by qualified personnel.
Do not use the device in environments with flammable gases, corrosive substances, or excessive vibration.
Verify all wiring connections are correct and secure to prevent malfunction or damage.
Alat ieu dirarancang pikeun pamakéan jero rohangan wungkul.

3. Produk Langkungview

The AUTONICS TC4Y-14R is a compact PID temperature controller offering high-precision control. It features a clear digital display and intuitive button interface for parameter setting.

AUTONICS TC4Y-14R PID Temperature Controller front view

Gambar 1: Hareupeun view of the AUTONICS TC4Y-14R PID Temperature Controller. The display shows four red digits for the process value and smaller indicators for SV (Set Value), AL1 (Alarm 1), OUT (Output), °F, and °C. Control buttons include an up arrow, MD (Mode), and a down arrow.

3.1. Komponén Panel hareup

tampilan PV: Shows the current process value (e.g., temperature).
SV Indicator: Illuminates when the set value is displayed or being adjusted.
AL1 Indicator: Illuminates when Alarm 1 is active.
Indikator OUT: Nyaangan nalika kaluaran kontrol aktip.
°F/°C Indicators: Show the selected temperature unit.
Tombol Naék / Turun: Used to adjust parameter values.
MD (Mode) Button: Used to navigate through parameter groups and confirm settings.

4. Setup jeung Instalasi

4.1. Pamasangan

The TC4Y-14R is designed for panel mounting. Ensure adequate space for ventilation and wiring connections. Avoid mounting near heat sources or areas with excessive dust or moisture.

4.2. Kabel

Refer to the wiring diagram on the side of the unit or in the full technical specifications for precise connections. Ensure all power is off before wiring.

Sasayogian tanaga: Connect 100-240VAC to the designated power terminals.
Input sénsor: Connect your temperature sensor (e.g., thermocouple, RTD) to the input terminals. Ensure correct polarity for thermocouples.
Control Output (Relay): Connect the load to the relay output terminals.
Control Output (SSR): Connect the Solid State Relay (SSR) input to the SSR output terminals.
Kaluaran Alarm (Opsional): If using, connect alarm devices to the alarm output terminals.

Catetan: Incorrect wiring can cause damage to the unit or connected equipment. Always double-check connections.

5. Parentah Operasi

5.1. Mimiti Power-Up

After completing all wiring, apply power to the unit. The display will show the current process value (PV).

5.2. Setting the Set Value (SV)

Pencét éta MD button briefly. The SV indicator will illuminate, and the display will show the current set value.
Ngagunakeun éta Up or Turun buttons to adjust the set value to your desired temperature.
Pencét éta MD button again to confirm the setting and return to PV display.

5.3. Parameter Setélan

Pikeun ngaksés parameter canggih (contona, konstanta PID, setélan alarm, jinis input), pencét sareng tahan tombol MD button for several seconds until the parameter group changes. Navigate through parameters using the MD button and adjust values with the Up/Turun buttons. Refer to the full technical manual for a complete list of parameters and their functions.

6. Pangropéa

The AUTONICS TC4Y-14R is designed for reliable operation with minimal maintenance.

beberesih: Lap panel hareup ku lawon anu lemes sareng garing. Ulah nganggo pembersih atanapi pangleyur anu abrasif.
Pamariksaan: Periodically check wiring connections for looseness or signs of damage.
Kalibrasi: If precise accuracy is critical, periodic calibration of the temperature sensor and controller may be required by a qualified technician.

7. Cara ngungkulan

Masalah	Mungkin Cukang lantaranana	Solusi
Teu aya tampilan/Pareuman	Teu aya catu daya; Kabelna salah	Check power connections and voltage; Verify wiring diagram.
Maca suhu teu akurat	Sensor faulty; Incorrect sensor type setting; Sensor not properly installed	Check sensor for damage; Verify input type parameter; Ensure sensor is correctly placed.
Kaluaran teu diaktipkeun	Wiring error; Set value too high/low; PID parameters incorrect	Check output wiring; Adjust SV; Review PID settings (P, I, D).
"HHHH" or "LLLL" on display	Sensor open circuit (HHHH) or short circuit (LLLL); Temperature out of range	Check sensor and wiring; Ensure operating temperature is within sensor's range.

8. Spésifikasi

Fitur	Rincian
Modél	TC4Y-14R
merek	AUTONICS
Métode kontrol	PID (Proportional-Integral-Derivative)
Kaluaran kontrol	Relay and SSR (Solid State Relay)
Sasayogian tanaga	100-240VAC
Tipe tampilan	LCD or LED (Digital)
Tipe Input	Universal (Thermocouple, RTD - specific types depend on configuration)
Asalna	Dijieun di Korea

9. Garansi jeung Rojongan

AUTONICS products are manufactured to high-quality standards. For specific warranty terms and conditions, please refer to the official AUTONICS website or contact your authorized distributor. Technical support is available through AUTONICS customer service channels.

Pikeun pitulung salajengna, mangga buka: www.autonics.com

	Lembar Data Pangontrol Suhu Tipe Saklar Toél Seri TC Autonics Lembar data lengkep pikeun Kontroler Suhu Tipe Saklar Sentuh Autonics TC Series, anu ngajéntrékeun fitur, spésifikasi, inpormasi pesenan, diménsi, diagram sambungan, fungsi, sareng penanganan kasalahan.
	Autonics SR2/SR3/SRH2/SRH3 Series 2/3-Phase SSR Instruction Manual Comprehensive instruction manual for Autonics SR2, SR3, SRH2, and SRH3 series 2/3-phase Solid State Relays (SSRs) with detachable and integrated heatsinks. Covers safety considerations, usage cautions, ordering information, dimensions, installation, connections, wiring, detailed specifications, and derating curves.
	Manual Instruksi Pangontrol Suhu Autonics Seri TC4 Explore the Autonics TC4 Series temperature controllers with this comprehensive instruction manual. Covers models TC4S, TC4SP, TC4Y, TC4M, TC4H, TC4W, TC4L, detailing specifications, installation, operation, and features for industrial temperature control.
	Manual Instruksi SSR Fase Tunggal Seri Autonics SRH1 Manual instruksi pikeun SSR Tipe Heatsink Terpadu Fase Tunggal Seri Autonics SRH1. Ngawengku spésifikasi, kaamanan, operasi, sareng diménsi pikeun modél tipe input ayeuna.
	Autonics TX Series LCD PID Suhu Controllers Manual Instruksi Instruksi manual pikeun Autonics TX Series LCD PID Suhu Controllers, ngawengku tinimbangan kaamanan, spésifikasi, informasi mesen, sambungan, sarta setélan parameter.
	Manual Instruksi Pangontrol Suhu PID Autonics Seri TK Detailed instruction manual for Autonics TK Series simultaneous heating and cooling PID temperature controllers. Covers specifications, ordering information, safety precautions, installation, and parameter settings for models like TK4N, TK4S, TK4SP, and more.