BISSELL CrossWave 17132 3-in-1 Multi-Surface Floor Cleaner User Manual

Produk Leuwihview

The BISSELL CrossWave 17132 is a versatile 3-in-1 multi-surface floor cleaner designed to vacuum, wash, and dry hard floors, carpets, and rugs simultaneously. This integrated cleaning system offers an efficient alternative to traditional vacuuming and mopping, providing thorough cleaning with less effort. Its dual tank technology ensures that clean water and formula are always separate from dirty water, guaranteeing a fresh clean every time.

Komponén Kaasup

Before beginning assembly, ensure all components are present in the packaging:

• BISSELL CrossWave 17132 Unit (Main Body and Handle)
• Multi-Surface Cleaning Formula (Detergent)
• Multi-Surface Brush Roll (Replacement Brush)
• Storage and Cleaning Tray (Station)

Image: The BISSELL CrossWave 17132 unit shown with its accompanying multi-surface cleaning formula, an extra brush roll, and the storage and cleaning tray.

Parentah Setup

Majelis

1. Selapkeun cecekelan kana awak utama unit nepika clicks aman kana tempatna.
2. Pastikeun tangki cai bersih dipasang kalayan leres di tukang unit.
3. Ensure the dirty water tank is properly seated on the front of the unit.

Ngeusian Tangki Cai Beresih

1. Cabut tangki cai bersih tina tonggong mesin.
2. Cabut cap dina handapeun bak.
3. Fill the tank with warm tap water up to the 'Water' fill line for the desired cleaning area (small or large).
4. Add the BISSELL Multi-Surface Cleaning Formula up to the corresponding 'Formula' fill line.
5. Replace the cap and reinsert the tank into the machine, ensuring it is securely latched.

Parentah Operasi

Powering On and Selecting Mode

1. Colokkeun kabel listrik kana stop kontak listrik grounded.
2. Press the power button located on the handle to turn on the machine.
3. Use the fingertip controls on the handle to select the appropriate cleaning mode: Lantai teuas or Karpét Daérah.

Prosés beberesih

To dispense cleaning solution, hold down the spray trigger located on the handle. Release the trigger to stop dispensing.

For best results, make a wet pass by holding the spray trigger and moving the machine slowly forward and backward. Then, make a dry pass by releasing the trigger and moving the machine over the same area to suction up the dirty solution.

Image: A user operating the BISSELL CrossWave 17132 on a hard floor, demonstrating its cleaning action on a liquid spill.

Image: The BISSELL CrossWave 17132 cleaning a tiled floor, effectively picking up scattered dry debris and wet messes.

Pangropéa sareng Perawatan

Ngosongkeun sareng Ngabersihan Tangki Cai Kotor

1. Pareuman teras cabut mesin.
2. Remove the dirty water tank from the front of the machine.
3. Carefully remove the filter and pour out the dirty water.
4. Rinse the tank and filter thoroughly with water. Allow the filter to air dry completely before reinserting.
5. Replace the filter and reattach the dirty water tank to the machine, ensuring it is securely latched.

Cleaning the Brush Roll and Brush Roll Window

1. Pareuman teras cabut mesin.
2. Cabut jandela gulungan sikat ku cara narik tabna ka luhur.
3. Remove the brush roll by grasping the tab and pulling it out.
4. Rinse the brush roll and brush roll window under running water. Remove any hair or debris.
5. Allow both to air dry completely before reassembling.
6. Reinsert the brush roll, ensuring it clicks into place, then reattach the brush roll window.

Gambar: A close-up view of the BISSELL CrossWave 17132's brush roll and base, highlighting the multi-surface brush for effective cleaning.

Using the Storage and Cleaning Tray

After each use, place the CrossWave on the storage and cleaning tray. Fill the tray with water up to the indicated line. Run the machine for approximately 10-20 seconds to rinse the brush roll and internal components. This helps prevent odors and maintains performance.

Pamérésan masalah

Machine Not Dispensing Solution

• Check if the clean water tank is properly filled and seated.
• Ensure the spray trigger is being held down during operation.
• Verify that the formula cap is securely tightened.

Nyeuseup goréng

• Pariksa naha tangki cai kotor pinuh sareng kedah dikosongkeun.
• Pastikeun tangki cai kotor dipasang kalayan leres sareng disegel.
• Inspect the brush roll and brush roll window for clogs or debris.
• Ngabersihan saringan sareng pastikeun éta garing sateuacan dipasang deui.

Mesin Henteu Hurungkeun

• Pastikeun kabel listrik parantos dicolokkeun kalayan pageuh kana stop kontak listrik anu tiasa dianggo.
• Pariksa pikeun sagala breakers circuit tripped.

Spésifikasi produk

Garansi sareng Rojongan

For warranty information, technical support, or to purchase replacement parts and cleaning formulas, please visit the official BISSELL website or contact BISSELL customer service. Always use genuine BISSELL replacement parts and cleaning formulas to ensure optimal performance and to maintain your warranty.

Teu aya pidéo produk resmi ti nu ngajual anu sayogi kanggo disematkeun dumasar kana data anu disayogikeun.