Satechi Aluminum USB-C 2.5-inch HDD/SSD Enclosure

Bubuka

This manual provides instructions for the installation and operation of your Satechi Aluminum USB-C 2.5-inch HDD/SSD Enclosure. This enclosure allows you to convert any 2.5-inch SATA hard drive (HDD) or solid-state drive (SSD) into a portable external storage device, utilizing a USB-C connection for data transfer speeds up to 10 Gbps.

Eusi pakét

• Satechi Aluminum USB-C 2.5-inch HDD/SSD Enclosure
• USB-C ka USB-C Cable
• Obeng Mini
• Pamasangan screws

Setup sareng Instalasi

Follow these steps to install your 2.5-inch HDD or SSD into the enclosure:

1. Buka Kandangna: Use the provided mini screwdriver to remove the two small screws located on the side of the enclosure. Carefully slide the internal tray out from the aluminum casing.

Image: Enclosure disassembled, revealing the internal tray and screws.
2. Selapkeun drive: Align your 2.5-inch SATA HDD or SSD with the SATA connector on the internal tray. Gently push the drive into the connector until it is firmly seated.


Image: Inserting a 2.5-inch SSD into the internal tray.

3. Amankeun Drive: Use the provided mounting screws to secure the HDD/SSD to the internal tray. Ensure the drive is stable and does not move.

Image: SSD fully inserted and secured in the tray.
4. Tutupkeun Kandangna: Carefully slide the internal tray, with the installed drive, back into the aluminum casing. Re-insert and tighten the two small screws to secure the enclosure.

Parentah Operasi

1. Nyambung ka Komputer: Use the included USB-C to USB-C cable to connect the enclosure to an available USB-C port on your computer.


Image: Enclosure connected to a laptop.

2. Indikator kakuatan: A blue LED indicator light on the enclosure will illuminate when connected and powered, indicating readiness for use. The LED will blink during data transfer activity.

Image: Enclosure with cable connected, showing the blue LED.
3. Ngaksés drive: Your computer should automatically detect the external drive. If it is a new drive, you may need to format it before use. Refer to your operating system's documentation for drive formatting procedures.
4. Mindahkeun Data: Séred jeung leupaskeun files to and from the external drive as you would with any other storage device. The enclosure supports data transfer speeds up to 10 Gbps, depending on your drive and computer's USB-C port capabilities.
5. Ngahapus Aman: Always safely eject the external drive from your operating system before disconnecting the cable to prevent data corruption.

Pangropéa

• Jaga kandang tetep bersih sareng bébas tina lebu. Anggo lawon anu lemes sareng garing pikeun ngabersihkeun.
• Hindarkeun alat ka suhu ekstrim, kalembaban, atanapi sinar panonpoé langsung.
• Do not attempt to disassemble the enclosure beyond the initial drive installation, as this may void the warranty.

Pamérésan masalah

• Drive Teu Dideteksi:
  • Ensure the USB-C cable is securely connected to both the enclosure and your computer.
  • Cobi sambungkeun ka port USB-C anu béda dina komputer anjeun.
  • Verify that the HDD/SSD is correctly seated within the enclosure's SATA connector.
  • If it is a new drive, ensure it has been formatted for your operating system.
• Laju Transfer Lambat:
  • Ensure your computer's USB-C port supports USB 3.1 Gen 2 (10 Gbps) for optimal performance.
  • The performance of the drive itself (HDD vs. SSD) will impact transfer speeds.
  • Consider using a high-quality, certified USB-C cable, especially if experiencing intermittent disconnections or slower-than-expected speeds.
• Enclosure Disconnects Acak:
  • This can sometimes be caused by an incompatible or low-quality USB-C cable. Try using a different, certified USB-C cable.
  • Pastikeun setelan daya komputer anjeun teu dikonpigurasi pikeun mareuman port USB pikeun ngahemat daya.

spésifikasi

Garansi sareng Rojongan

For warranty information and technical support, please refer to the official Satechi websitus atanapi ngahubungan layanan palanggan maranéhanana langsung. Simpen resi pameseran anjeun pikeun klaim jaminan.