Bubuka
Thank you for choosing the BN-LINK Countdown Digital Wall Timer Switch. This manual provides essential information for the safe installation, operation, and maintenance of your new timer switch. Please read these instructions thoroughly before installation and use, and retain them for future reference.
Émbaran Kasalametan
- PERHATOSAN: Résiko Setrum Listrik. Installation requires working with high voltage wiring. Always turn off power at the circuit breaker before installation.
- This device requires a Kawat Netral for proper operation. Ensure your electrical box has a neutral wire (typically white) before attempting installation.
- Upami anjeun henteu yakin ngeunaan bagian mana waé tina prosés pamasangan, konsultasi ka tukang listrik anu mumpuni.
- Rated 125V, 60 Hz, 15A/1875W Resistive or General Purpose, 10A/1250W Ballast or Tungsten, ½ HP, TV-5.
- ETL listed, conforms to UL Std. 60730-1, 60730-2-7.
Eusi pakét
- BN-LINK Countdown Digital Wall Timer Switch
- Piring Tembok
- Kawat Kacangan
- Pamasangan screws
- Instruksi Manual
spésifikasi
| Fitur | Spésifikasi |
|---|---|
| Modeu Operasi | HIRUP |
| Peunteun ayeuna | 15 Amps |
| Operasi Voltage | 125 volt |
| Wattage | 1875 Watt |
| Tipe Kontak | Biasana Buka |
| Tipe Panyambung | Dikabel |
| Ukuran (L x W x H) | 4.2 x 1.8 x 2 inci |
| Item Beurat | 5.6 ons |
| Alat nu cocog | Incandescent, fluorescent, and LED lighting, bathroom exhaust fans, heaters |
Setup sareng Instalasi
Sateuacan anjeun ngamimitian: Turn off power at the circuit breaker for the switch location. Verify power is off using a voltage panguji.
Parentah Wiring
- Identipikasi Kawat: Carefully remove your existing switch and identify the Hot, Load, Neutral, and Ground wires in your wall box. A neutral wire (typically white) is required.
- Sambungkeun kawat: Use the provided wire nuts to connect the BN-LINK timer switch wires to your household wires as follows:
- Black Wire (Timer) ka Hot Wire (Wall Box)
- Red Wire (Timer) ka Load Wire (Wall Box)
- White Wire (Timer) ka Neutral Wire (Wall Box)
- Green Wire (Timer) ka Ground Wire (Wall Box)
- Wiring Aman: Ensure all wire connections are secure and insulated with wire nuts.
Pamasangan sareng Finishing
- Insert Switch: Carefully push the wired timer switch into the wall box.
- Saklar Aman: Use the provided screws to secure the timer switch to the wall box.
- Ngagantelkeun Piring Tembok: Mount the included wall plate over the switch.
- Mulangkeun Daya: Hurungkeun deui kakuatan dina circuit breaker.
Pituduh Pidéo Instalasi
Parentah Operasi
1. Initialization
When the timer is first powered, all indicator lights will briefly illuminate and then turn off after a self-diagnosis process. This indicates the timer is ready for use.
2. Setting a Countdown Program
To activate a countdown, simply press the button corresponding to your desired time (5, 10, 20, 30, 45, or 60 minutes). The indicator light on the selected button will illuminate, and the countdown will begin. The connected device will turn off automatically once the countdown is complete.
3. Shifting to Another Countdown Program
If a countdown is active and you wish to change the duration, press a different countdown button. The indicator light on the previously active button will turn off, and the light on the newly selected button will illuminate. The new countdown program will then begin.
4. Activating the Daily Repeat Function
To enable the daily repeat function, press the ULANGAN button while a countdown program is running. The indicator light on the ULANGAN button will illuminate. The current program will automatically run again at the same time on the following day.
5. Deactivating the Daily Repeat Function (2 Ways)
There are two methods to deactivate the daily repeat function:
- Press REPEAT Button: Pencét éta ULANGAN button again. Its indicator light will turn off. This will deactivate the repeat function for any ongoing program.
- Press ON/OFF Button: Pencét éta ON/OFF button. This will terminate the ongoing program and also deactivate the daily repeat function.
6. Termination of a Countdown Program
A countdown program will terminate automatically when its set time expires. The indicator light for that program will turn off, and the power output to the connected device will be cut off.
7. Always On Mode
If a countdown is already running, or if the daily repeat function is active, press the ON/OFF button twice to set the timer to 'Always On' mode. The ON/OFF indicator light will illuminate, and the device will remain powered indefinitely.
If the timer is in 'Off' mode, press the ON/OFF button once to set the timer to 'Always On' mode. The ON/OFF lampu indikator bakal nyaangan.
8. Terminating Always On Mode
To terminate 'Always On' mode:
- Press ON/OFF Button: Pencét éta ON/OFF kancing sakali. The ON/OFF indicator light will turn off, and the power output will be cut off.
- Select Countdown Program: Press any of the preset countdown buttons (5, 10, 20, 30, 45, or 60 minutes). This will initiate a new countdown program and terminate 'Always On' mode.
9. Restarting a Running Countdown Program
To restart a running countdown program:
- Terminate and Re-select: Pencét éta ON/OFF button to terminate the current program, then immediately press the desired countdown button to restart it.
- Shift Program: Alternatively, press a different countdown button, and then press the original countdown button you wish to restart.
Pangropéa
To maintain your BN-LINK Countdown Digital Wall Timer Switch, ensure the power is off at the circuit breaker before cleaning. Wipe the surface with a soft, damp cloth. Do not use harsh chemicals or abrasive cleaners. Regular inspection for any loose wiring or damage is recommended.
Pamérésan masalah
- Timer teu hurung: Check the circuit breaker to ensure power is supplied. Verify all wiring connections are secure, especially the neutral wire.
- Countdown not starting: Ensure a specific time button is pressed and its indicator light is on.
- Repeat function not working: Confirm the REPEAT indicator light is illuminated after activation. If not, press the REPEAT button again while a countdown is active.
- Device not turning off: Check if the timer is in 'Always On' mode (ON/OFF indicator illuminated). If so, press the ON/OFF button to turn it off.
Garansi sareng Rojongan
BN-LINK products are designed for reliability and performance. For any questions regarding installation, operation, or troubleshooting, please contact BN-LINK customer support. We are always here to assist you.
For further information, please refer to the included guide or visit our official websitus.
