Manual Instruksi Gergaji Pita Dua Kagancangan 10 Inci WEN 3962T

1. Bubuka

This instruction manual provides essential information for the safe and effective operation, assembly, maintenance, and troubleshooting of your WEN 3962T 10-Inch Two-Speed Band Saw. Please read this manual thoroughly before operating the tool and keep it for future reference. Understanding and following these instructions will ensure optimal performance and extend the life of your band saw.

2. Pitunjuk Kasalametan Umum

Always prioritize safety when operating power tools. Failure to follow safety guidelines can result in serious injury or property damage.

• Baca Sadaya Parentah: Familiarize yourself with the tool's operation and safety procedures.
• Nganggo panyalindungan panon: Always wear ANSI-approved safety goggles or a face shield.
• Nganggo panyalindungan dédéngéan: Paké earplugs atawa earmuffs salila operasi.
• Jaga Wewengkon Gawé Bersih: Daérah anu kabongkar sareng bangku ngondang kacilakaan.
• Ngahindarkeun Lingkungan Bahaya: Ulah make parabot kakuatan dina damp atanapi lokasi baseuh, atanapi ngalaan aranjeunna hujan. Tetep aréa damel ogé hurung.
• Jauhkeun Barudak: Kabéh sémah kudu dijaga jarak aman ti wewengkon gawé.
• Workpiece Aman: Salawasna nganggo clamps atawa catok pikeun nyekel benda kerja.
• Do Not Force Tool: Éta bakal ngalaksanakeun padamelan anu langkung saé sareng langkung aman dina tingkat anu dirarancangna.
• Paké Alat Katuhu: Ulah maksakeun pakakas leutik atawa alat tambahan pikeun ngalakukeun padamelan pakakas beurat.
• Pakéan anu leres: Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Non-slip footwear is recommended. Wear protective hair covering to contain long hair.
• Ngajaga Alat-alat kalayan ati-ati: Jaga alat anu seukeut sareng bersih pikeun pagelaran anu pangsaéna sareng paling aman. Turutan pitunjuk pikeun pelumas sareng ngarobih aksesoris.
• Alat pegatkeun sambungan: Disconnect tools from power supply before servicing, when changing accessories, or when not in use.
• Hindarkeun Awal Kahaja: Make sure switch is off when plugging in.
• Pariksa Bagian Rusak: Sateuacan nganggo alat salajengna, penjaga atanapi bagian sanésna anu ruksak kedah dipariksa sacara saksama pikeun nangtukeun yén éta bakal beroperasi leres sareng ngalaksanakeun fungsi anu dimaksud.

3. Eusi Paket

Verify that all items are present upon unpacking. If any parts are missing or damaged, contact WEN customer service immediately.

• WEN 10-Inch Two-Speed Band Saw
• Nangtung
• Flexible Work Light
• 3-in-1 Dust Port (1-3/4, 2-3/4, 4 inches)
• Fence for straight cuts
• Miter Gauge for angled cuts
• Band Saw Blade (72-inch, 1/8 to 1/2 inches in size)

Figure 3.1: Complete WEN 3962T Band Saw with stand and worklight.

4. Setup jeung Majelis

Follow these steps for proper assembly and initial setup of your band saw.

1. Kumpulkeun Stand: Securely attach the stand components according to the included hardware. Ensure all bolts are tightened to provide a stable base for the saw.
2. Mount the Band Saw: Carefully lift the band saw onto the assembled stand and secure it using the provided mounting hardware.
3. Pasang Blade:
   • Open the blade covers.
   • Sacara saksama posisikeun bilahna di sabudeureun roda luhur sareng handap, pastikeun huntuna nunjuk ka handap nuju méja.
   • Adjust the blade tension using the tension knob until the blade is taut but not overly stressed.
   • Adjust the blade guides and thrust bearings to ensure proper blade tracking and support.
   

   Gambar 4.1: Internal view showing blade wheels and tensioning.
   

   Figure 4.2: Close-up of blade guide and thrust bearings.

4. Install the Work Table: Attach the spacious 14-1/8 x 12-1/2 inch work table. Ensure it is level with the blade and can be securely locked at various angles up to 45 degrees.
5. Attach the Fence and Miter Gauge: Install the fence for straight cuts and the miter gauge for angled cuts onto the work table.
6. Connect the Work Light: Position the flexible work light to illuminate the worktable effectively.
7. Connect Dust Collection: Attach a dust extractor hose to the 3-in-1 dust port (1-3/4, 2-3/4, or 4 inches) to maintain a clean work environment.

Figure 4.3: Work table with fence and miter gauge installed.

Figure 4.4: Flexible work light in position.

Figure 4.5: 3-in-1 dust port for dust collection.

5. Parentah Operasi

Understand the features and controls of your band saw for efficient and safe operation.

• Saklar kakuatan: Locate the main power switch for turning the saw on and off.
• Pilihan Speed: The saw operates at two speeds: 1520 FPM (Feet Per Minute) and 2620 FPM. Select the appropriate speed for your material. Lower speeds are generally for harder materials or intricate cuts, while higher speeds are for softer woods and faster cutting.
• Work Table Adjustment: The work table can be swiveled up to 45 degrees for angled cuts. Loosen the locking mechanism, adjust to the desired angle, and re-tighten securely.
• Using the Fence: For straight cuts, position the fence parallel to the blade and lock it in place.
• Ngagunakeun Miter Gauge: For precise angled cross-cuts, use the miter gauge. Adjust it to the desired angle and guide the workpiece against it.
• Prosedur motong:
  1. Ensure the workpiece is free of nails, screws, or other foreign objects.
  2. Adjust the blade guide assembly so it is approximately 1/8 inch above the workpiece.
  3. Turn on the saw and allow the blade to reach full speed before beginning the cut.
  4. Feed the workpiece slowly and steadily into the blade. Do not force the material.
  5. Keep hands clear of the blade path. Use a push stick for smaller pieces.

6. Pangropéa

Regular maintenance ensures the longevity and safe operation of your band saw.

• Gantian sabeulah: Replace dull or damaged blades promptly. Always disconnect power before changing blades.
• beberesih: Regularly clean sawdust and debris from the work table, blade guides, and internal components. Use a vacuum or compressed air.
• Lubrication: Periodically lubricate moving parts as specified in the full product manual (not provided here).
• Blade Tension: Check blade tension before each use. Proper tension prevents blade breakage and ensures accurate cuts.
• Pituduh agul jeung bantalan: Inspect blade guides and thrust bearings for wear and proper adjustment. Replace worn components as needed.
• Table Waxing: Apply paste wax to the cast iron table to reduce friction and prevent rust.

7. Cara ngungkulan

Tingali kana bagian ieu pikeun masalah umum sareng solusina.

8. Spésifikasi

9. Garansi jeung Rojongan

The WEN 3962T 10-Inch Two-Speed Band Saw comes with a 2-taun jaminan kawates for residential use. For commercial use, a 90-day warranty applies. This warranty covers defects in material and workmanship. For warranty claims, technical assistance, or to order replacement parts, please contact WEN customer service.

For further assistance, visit the official WEN website or contact their customer support line. Please have your model number (3962) and purchase information ready when contacting support.