Enttec Open DMX USB Lighting Interface User Manual

1. Bubuka

The Enttec Open DMX USB is an entry-level DMX interface designed to provide a simple and cost-effective solution for controlling DMX lighting fixtures from a computer. It is ideal for basic DMX control, amateur lighting applications, and troubleshooting DMX setups. This device connects to your computer via USB and provides a 5-pin DMX output.

Image 1.1: The Enttec Open DMX USB device, showcasing its compact design and primary connections.

2. Émbaran Kasalametan

• Do not expose the device to rain or moisture. This unit is intended for indoor use only.
• Ulah nyabut panutup; euweuh bagian-pamaké-serviceable jero.
• Never connect DMX GND to an electrical 'earth' connection.
• For additional flexibility and increased protection, Enttec recommends the use of a DMX splitter.

3. Setélan

3.1. Sarat Sistim

• Operating System: Windows XP, Windows 7, Windows 8, Windows 10, macOS.
• Port USB 2.0 sayogi.
• Compatible DMX control software.

3.2. Pamasangan supir

The Open DMX USB is discovered as a USB Serial Device or virtual COM Port depending on the FTDI driver installed on your system. Drivers are typically installed automatically by your operating system when the device is first connected. If not, please visit the official Enttec websitus pikeun unduhan driver panganyarna.

3.3. Konéksi Hardware

1. Connect the Enttec Open DMX USB device to an available USB port on your computer using a standard USB Type B cable. The device is designed to be powered from the computer over USB.
2. Connect the 5-pin DMX XLR output of the Enttec Open DMX USB to the DMX input of your first DMX lighting fixture or DMX splitter. Ensure all DMX cables are properly terminated.

Image 3.1: Application diagram illustrating the connection flow from computer to DMX fixtures via the Open DMX USB.

4. Parentah Operasi

The Enttec Open DMX USB works with a wide range of third-party DMX control software. Once connected and drivers are installed, your software should recognize the device as a DMX output interface.

4.1. Kompatibilitas Parangkat Lunak

This device is compatible with various DMX software applications. It provides a single DMX universe (512 channels) of output. The specific features and capabilities will depend on the software used.

Gambar 4.1: Leuwihview of key features and intended uses of the Open DMX USB.

4.2. Operasi dasar

1. Launch your preferred DMX control software.
2. In the software's settings or preferences, select the Enttec Open DMX USB as your DMX output device.
3. Configure your DMX fixtures within the software, assigning them to specific DMX channels.
4. Begin sending DMX data from your software to control your lighting fixtures.

The device outputs up to 512 channels, with the exact number of usable channels depending on the software's capabilities.

5. Pangropéa

The Enttec Open DMX USB is a robust device designed for reliable operation. It requires minimal maintenance.

• Jaga alat tetep beresih sareng leupas tina lebu. Anggo kaén anu lemes sareng garing pikeun beberesih.
• Hindarkeun ngalaan alat ka suhu atanapi kalembaban anu ekstrim.
• Ulah nyobian muka casing or modify the device, as this will void the warranty and may cause damage.

6. Cara ngungkulan

6.1. Device Not Recognized by Computer

• Pastikeun kabel USB disambungkeun pageuh kana alat sareng komputer.
• Coba port USB anu béda dina komputer anjeun.
• Verify that the necessary FTDI drivers are installed. Check your computer's Device Manager (Windows) or System Information (macOS) for the device. If drivers are missing, download them from the Enttec websitus.
• Balikan deui komputer anjeun.

6.2. No DMX Output / Lights Not Responding

• Confirm that the Enttec Open DMX USB is selected as the output device within your DMX control software.
• Check all DMX cable connections between the interface and your fixtures. Ensure they are 5-pin DMX cables and are not damaged.
• Verify that your DMX fixtures are properly addressed and patched within your software.
• Ensure DMX termination is correctly applied at the end of your DMX chain.
• Test with a different DMX fixture or a DMX tester if available.
• Close and reopen your DMX control software.

7. Spésifikasi

Image 7.1: Detailed specifications from the product datasheet.

Image 7.2: Physical dimensions of the Enttec Open DMX USB.

8. Garansi

The Enttec Open DMX USB comes with a 3-year return-to-base manufacturer warranty. For warranty claims or service, please contact Enttec support or your authorized reseller.

9. Rojongan

For further support, driver downloads, software compatibility information, and frequently asked questions, please visit the official Enttec websitus:

www.enttec.com

You may also contact Enttec customer service directly for technical assistance.