Bubuka
The Reloop NEON is a compact and powerful USB modular pad controller designed for use with Serato DJ. It provides an intuitive interface for triggering samples, cues, loops, and effects, enhancing performance capabilities for DJs. This manual provides comprehensive instructions for setup, operation, maintenance, and troubleshooting of your Reloop NEON controller.
Figure 1: Reloop NEON USB Modular Pad Controller. This image displays the top view of the controller, highlighting its eight illuminated RGB pads and various control buttons and knobs.
Disetél
1. Konéksi Hardware
- Sambungkeun kabel USB: Connect the supplied USB cable from the Reloop NEON to an available USB port on your computer (Windows or Mac).
- kakuatan: The NEON controller is USB bus-powered and does not require an external power supply.
- Smart Link Function: For expanded control, two NEON controllers can be connected via the smart link function, utilizing a single USB port on your computer. Connect the first NEON to your computer, then connect the second NEON to the first using a standard USB cable.
Figure 2: Two Reloop NEON controllers connected. This image illustrates how two NEON units can be linked together, expanding the available control surface.
2. Pamasangan parangkat lunak
- Serato DJ: Ensure you have Serato DJ installed on your computer. The Reloop NEON is designed for seamless integration with Serato DJ.
- Supir: In most cases, the NEON is class-compliant and does not require specific driver installation for basic functionality. If issues arise, check the official Reloop website for any necessary drivers or firmware updates.
Operating the Reloop NEON
The Reloop NEON features 8 ultra-low-latency, touch-sensitive RGB drum pads with aftertouch, along with various control buttons and two endless push encoders. The pads provide visual feedback through smart color-coding, indicating the current mode and status.
Modeu kinerja
The NEON offers 8 distinct performance modes, accessible for up to 4 decks. These modes are selected using the dedicated buttons above the pads.
- Sampler: Triggers samples loaded into Serato DJ's SP6 sampler. Pads illuminate to show sampstatusna.
- Pad FX: Controls various effects within Serato DJ, allowing for dynamic manipulation of audio.
- Pangiris: Divides a section of the track into 8 slices across the pads, allowing for re-sequencing and creative playback.
- Looped Slicer: Similar to Slicer, but the slices are continuously looped.
- Pitunjuk: Sets and triggers hot cue points within your tracks.
- Balikkeun: Records and plays back cue trigger sequences on the fly, enabling real-time remixing.
- Hot Loop: Instantly creates and triggers loops of various lengths.
- Loop Manual: Provides manual control over loop in and out points.
Figure 3: Reloop NEON performance modes. This image highlights the "PERFORMANCE MODE" section with buttons for Sampler, Pad FX, Slicer, Looped Slicer, Cue, Flip, Hot Loop, and Manual Loop.
Kadali Langkungview
- RGB Drum Pads: 8 velocity-sensitive pads for triggering various functions. Their color indicates the active mode or status.
- Endless Push Encoders: Two encoders located on the left and right sides.
- Left Encoder: Typically used for track navigation and sampler volume control.
- Right Encoder: Typically used for loop editing and other parameter adjustments.
- Bank/Deck Buttons: Allows selection of different banks for pads or control over specific decks (1-4).
- Tombol Shift: Activates secondary functions printed below or next to primary controls.
Pangropéa
- beberesih: Use a soft, dry cloth to clean the surface of the controller. Avoid abrasive cleaners or solvents.
- Panyimpenan: Simpen alat dina tempat anu tiis sareng garing jauh tina sinar panonpoé langsung sareng suhu anu ekstrim.
- Penanganan: Avoid dropping the unit or subjecting it to strong impacts. Do not spill liquids on the controller.
Pamérésan masalah
| Masalah | Mungkin Cukang lantaranana | Solusi |
|---|---|---|
| Controller not recognized by computer. | USB cable issue, incorrect USB port, driver problem. | Try a different USB port or cable. Restart your computer. Check the Reloop website for specific drivers if needed. |
| Pads not responding in Serato DJ. | Serato DJ not configured correctly, incorrect mode selected. | Ensure Serato DJ recognizes the NEON in its MIDI settings. Verify the correct performance mode is active on the NEON. |
| Pads are not illuminating. | No power, software communication issue. | Ensure the NEON is properly connected via USB. Check Serato DJ connection. |
| Encoder knob is erratic or unresponsive. | Wear and tear, dust/debris. | Clean around the encoder. If the issue persists, contact Reloop support for service. |
spésifikasi
- merek: Reloop
- model: Neon
- Beurat barang: 12.6 ons (0.36 Kilogram)
- Ukuran produk: 8.8 x 4.8 x 0.63 inci
- Téknologi konektipitas: USB
- Antarmuka Hardware: USB 2.0
- Alat anu cocog: Computer (Windows, Mac), Tablet (iOS) with USB connectivity
- Parangkat Lunak anu Dirojong: Serato DJ
- Jumlah kenop kibor: 22 (referring to pads and buttons)
- Titimangsa munggaran sadia: 18 Séptémber 2014
Garansi sareng Rojongan
For warranty information and technical support, please refer to the official Reloop website or contact your authorized Reloop dealer. Keep your proof of purchase for warranty claims.
Reloop Official Websitus: www.reloop.com
