Bubuka
This manual provides essential information for the safe and effective use of the Hakko CHP TR-20-TM Micro Soft Wire Cutter. This precision tool is designed for cutting integrated circuit (IC) pins and soft wires up to 22 AWG (0.6mm).
Figure 1: Hakko CHP TR-20-TM Micro Soft Wire Cutter. This image displays the tool's overall design, highlighting its red and black ergonomic handles and the precise, angled cutting jaws.
Fitur produk
- Reverse-Cut Micro Soft-Wire Cutter: Features an 8mm long jaw with a reverse angle head, specifically designed for flush-cutting IC pins up to 22 gauge (0.6mm).
- Angled Cutting Surface: The 48-degree reverse angled cutting surface facilitates precise cutting of closely-spaced IC pins.
- Konstruksi awét: Constructed from 2.0mm heat-treated carbon steel for enhanced durability and extended tool life.
- Operasi lemes: Precision-ground holes and surfaces ensure smooth movement of the cutting jaws.
- Reduced Operator Fatigue: An internal spring mechanism automatically returns the tool to the open position after each cut, minimizing hand strain.
- Desain ergonomis: Dolphin-style nonslip hand grips provide comfort and control during prolonged use.
- Perlindungan leungeun: A curved fore-edge on the handles protects hands from cutting surfaces.
- Résistansi korosi: Parkerized surfaces prevent glare and increase the tool's resistance to corrosion.
Disetél
The Hakko CHP TR-20-TM Micro Soft Wire Cutter is ready for use out of the packaging. No assembly is required.
- Inspeksi Awal: Before first use, inspect the tool for any signs of damage or manufacturing defects. Ensure the jaws align properly and the spring mechanism operates smoothly.
- Kabersihan: Ensure the cutting jaws are clean and free of debris before use to maintain optimal cutting performance.
Parentah Operasi
Follow these instructions for safe and effective operation of the wire cutter.
- Kasalametan munggaran: Always wear appropriate eye protection when using cutting tools to prevent injury from flying debris.
- Pakem: Hold the cutter firmly with the ergonomic handles. The nonslip grips are designed for comfort and control.
- Posisi: Position the wire or IC pin to be cut between the jaws. For flush cuts on IC pins, align the reverse-angled jaw as close as possible to the circuit board or component body.
- Kapasitas motong: Do not attempt to cut wires or materials exceeding the maximum capacity of 22 AWG (0.6mm) for soft wire. Cutting harder or thicker materials can damage the tool's jaws.
- Aksi motong: Apply steady, firm pressure to the handles to close the jaws and make the cut. The internal spring will reopen the jaws automatically upon release.
- pembuangan: Dispose of cut wire pieces responsibly.
Pangropéa
Proper maintenance ensures the longevity and performance of your Hakko wire cutter.
- beberesih: After each use, wipe the jaws and handles with a clean, dry cloth to remove any debris or residue. For stubborn grime, a slightly damp lawon bisa dipaké, dituturkeun ku panggaringan tuntas.
- Lubrication: Sacara berkala, teteskeun saeutik oli mesin hampang kana titik poros pikeun mastikeun operasi anu lancar sareng nyegah karat. Lap oli anu kaleuleuwihi.
- Panyimpenan: Store the tool in a dry environment to prevent corrosion. Keep the jaws closed when not in use to protect the cutting edges.
- Hindarkeun Drop: Dropping the tool, especially on hard surfaces, can misalign or damage the precision jaws.
Pamérésan masalah
This section addresses common issues you might encounter with your wire cutter.
| Masalah | Mungkin Cukang lantaranana | Solusi |
|---|---|---|
| Jaws do not close completely or align properly. | Debris caught between jaws or pivot point; tool has been dropped or damaged. | Clean jaws thoroughly. If damage is suspected, discontinue use and consider replacement. |
| Cutting performance is poor or requires excessive force. | Dull or damaged cutting edges; attempting to cut material beyond capacity. | Inspect cutting edges for nicks or wear. Ensure material is within 22 AWG (0.6mm) soft wire limit. Replace if edges are significantly damaged. |
| Handles feel stiff or sticky. | Lack of lubrication at the pivot point; accumulation of dirt. | Clean the pivot area and apply a small amount of light machine oil. |
spésifikasi
| Atribut | Rincian |
|---|---|
| Nomer modél | TR-20-TM |
| Tipe Rahang | Reverse-cut, Micro Flush-cut |
| Jaw Length | 8 mm |
| Sudut Rahang | 48-degree reverse angle |
| Kamampuh motong maksimum | 22 AWG (0.6mm) soft wire / IC pins |
| Bahan Pangwangunan | 2.0mm Heat-treated Carbon Steel |
| Bahan cecekelan | Alloy Steel with Nonslip Grips |
| Warna | Beureum |
| Item Beurat | 0.1 Pon (kira-kira 45 gram) |
| Produsén | Quality Hand Tools |
Garansi sareng Rojongan
For warranty information or technical support regarding your Hakko CHP TR-20-TM Micro Soft Wire Cutter, please contact American Hakko Products directly. American Hakko Products manufactures soldering and desoldering tools and is headquartered in Valencia, CA.
Please refer to the official Hakko website or your purchase documentation for the most current warranty terms and contact details.
Pabrikan: Quality Hand Tools (as listed on product specifications, associated with Hakko brand)
merek: Hakko
Websitus: www.hakko.com