Manual pamaké

1. Bubuka

This manual provides detailed instructions for the installation, operation, and maintenance of your WAC Lighting EN-2460-RB2 Remote Enclosed Electronic Transformer. This Class 2, UL & cUL listed transformer is designed to provide a reliable 24V output from a 120V input, ideal for various low voltage aplikasi cahaya.

Image 1: WAC Lighting EN-2460-RB2 Electronic Transformer

Mangga baca manual ieu tuntas saméméh instalasi tur nyimpen eta pikeun rujukan ka hareup.

2. Émbaran Kasalametan

Salawasna patuh kana kode sareng peraturan listrik lokal. Pamasangan kedah dilakukeun ku tukang listrik anu mumpuni.

• Résiko Setrum Listrik: Pegatkeun sambungan kakuatan dina breaker sirkuit saméméh instalasi atawa ngalayanan.
• Class 2 Safety: This transformer is a Class 2 device, meaning its output is intrinsically safer, limiting current to no greater than 5 amps per compartment.
• UL & cUL Listed: Certified for damp locations, ensuring safety and compliance.
• Proposisi 65 Peringatan: Produk ieu tiasa ngalaan anjeun kana bahan kimia anu dipikanyaho ku Nagara Bagian California tiasa nyababkeun kanker sareng cacad lahir atanapi gangguan réproduktif anu sanés. Cuci leungeun saatos dianggo.
• Ulah ngaleuwihan kapasitas beban maksimum 60W.
• Ensure proper ventilation around the transformer.

3. Fitur Produk

• Masukan Voltage: 120V AC
• Kaluaran Voltage: 24V AC
• Kapasitas Beban Maksimum: 60 Watt
• Minimum Load Requirement: 1W, supporting low-load LED systems.
• Soft start, short circuit, and overload protection features for enhanced durability and safety.
• Designed for use with WAC Lighting low voltage under cabinet and recessed lighting systems.
• Compatible with electronic low voltage (ELV) dimmers for smooth and continuous dimming.
• Features knockouts on three sides with clips for line voltage kabel.
• Enclosed electronic transformer, UR (UL ready) component.

4. Setup jeung Instalasi

4.1. Pedoman Umum Kabel

The enclosure cover is designed for easy removal to facilitate wiring. The transformer includes knockouts on three sides with clips for secure line voltage sambungan kabel.

• Primary Wiring (Input 120V AC): Connect the 120V AC input to the primary side of the transformer. Ensure all connections are secure and comply with local electrical codes.
• Secondary Wiring (Output 24V AC): For Class 2 transformers, secondary wiring does not require conduit sheathed cable or clamp wiring techniques. Non-metallic sheathed cable may be used for secondary wiring in walls and ceilings, simplifying installation.
• Always use for initial installations to ensure safe and primary side connections within a wiring compartment.

4.2. Dimming

This transformer is designed for smooth and continuous dimming when used with an electronic low voltage (ELV) dimmer. It is crucial that dimmers are always installed on the sisi primér of the transformer (120V input side) to ensure proper operation and prevent damage.

Image 2: Dimensional Drawing of EN-2460-RB2 Transformer (Dimensions: 6" L x 3.25" W x 2.625" H)

5. Parentah Operasi

Once properly installed and wired, the transformer will convert the 120V AC input to 24V AC output for your low voltage lighting system. Operation is automatic upon power supply.

• Dimming: If an electronic low voltage (ELV) dimmer is installed on the primary side, you can control the brightness of your connected low voltage lights. Adjust the dimmer to achieve the desired light level.
• Pastikeun total wattage of connected fixtures does not exceed the transformer's 60W maximum load capacity and meets the 1W minimum load requirement for optimal performance, especially with LED products.

6. Pangropéa

The WAC Lighting EN-2460-RB2 transformer is designed for long-term, maintenance-free operation. No user-serviceable parts are inside. For cleaning, ensure power is disconnected and wipe the exterior with a dry, soft cloth. Do not use abrasive cleaners or solvents.

7. Cara ngungkulan

If you experience issues with your transformer, please review masalah umum sareng solusi ieu:

• Teu aya Kaluaran Cahaya:
  - Verify that the 120V AC input power is active at the primary side of the transformer.
  - Check all wiring connections for looseness or incorrect polarity.
  - Ensure the total load of connected fixtures does not exceed 60W and meets the 1W minimum load.
• Lampu kedip-kedip:
  - This can often be caused by an incompatible dimmer or a load that is too low for the dimmer/transformer combination. Ensure you are using an electronic low voltage (ELV) dimmer.
  - Verify the minimum load requirement (1W) is met.
• Dimming Issues (e.g., not dimming smoothly, limited range):
  - Confirm that the dimmer is an ELV type and is installed on the primary (120V) side of the transformer.
  - Some dimmers may require adjustment of their high-end or low-end trim levels. Refer to your dimmer's instruction manual for specific settings.
• Protéksi Kaleuwihan Beban Diaktipkeun:
  - If the transformer shuts off, it may be due to an overload. Disconnect some fixtures to reduce the total wattage below 60W and then cycle the power to reset the transformer.

If problems persist after attempting these solutions, contact a qualified electrician or WAC Lighting customer support.

8. Spésifikasi

9. Garansi jeung Rojongan

The WAC Lighting EN-2460-RB2 Electronic Transformer comes with a Five (5) year manufacturer limited warranty. Garansi ieu nyertakeun cacad dina bahan sareng pagawean dina panggunaan normal.

For warranty claims, technical support, or further assistance, please contact WAC Lighting directly. You can find more information and contact details on the official WAC Lighting websitus atanapi ngalangkungan halaman toko Amazon na: WAC Lighting Amazon Store.