Lithonia Lighting EDG 1 R EL M6 LED Emergency Exit Sign User Manual

Model: EDG 1 R EL M6

1. Bubuka

This manual provides comprehensive instructions for the installation, operation, and maintenance of the Lithonia Lighting EDG 1 R EL M6 LED Emergency Exit Sign. This edge-lit sign is designed for emergency egress lighting in commercial and institutional environments, ensuring clear visibility during power outages.

The EDG 1 R EL M6 features a durable aluminum construction, energy-efficient LED illumination, and a reliable battery backup system. Adherence to these instructions will ensure proper function and compliance with safety standards.

2. Émbaran Kasalametan

Baca sagala parentah: Before beginning installation or maintenance, carefully read and understand all instructions provided in this manual.
Pegatkeun kakuatan: Always disconnect power at the circuit breaker before installing, servicing, or cleaning the unit. Failure to do so may result in electric shock or serious injury.
tanaga mumpuni: Installation, servicing, and testing must be performed by qualified personnel in accordance with all national and local electrical codes and safety regulations.
UL 924 minuhan: This product is designed to meet UL 924 standards for emergency lighting and power equipment. Ensure all installations comply with these and other applicable standards.
Penanganan batré: The unit contains a sealed, maintenance-free nickel-cadmium battery. Do not attempt to open or service the battery. Dispose of batteries according to local regulations.
Kaayaan lingkungan: Install in locations where ambient temperatures are within the specified operating range. Do not install near gas or electric heaters.

3. Eusi Paket

Pastikeun yén sadaya komponén aya sareng henteu ruksak nalika muka bungkusan:

Lithonia Lighting EDG 1 R EL M6 LED Emergency Exit Sign (Battery-Powered, Red)
Mounting Hardware (typically includes screws, anchors, and canopy)
Instruction Sheet / Wiring Diagram

4. Setup jeung Instalasi

The EDG 1 R EL M6 is designed for surface mounting. Ensure the mounting surface is structurally sound and capable of supporting the fixture's weight.

4.1 Pilihan pamasangan

This unit supports various surface mounting configurations. Refer to the included wiring diagram for specific instructions on ceiling, wall, or end mounting.

Lithonia Lighting EDG 1 R EL M6 LED Emergency Exit Sign, red letters, top-down view.

Gambar: luhur-handap view of the Lithonia Lighting EDG 1 R EL M6 LED Emergency Exit Sign, showing the brushed aluminum housing and clear acrylic panel with red 'EXIT' letters.

4.2 Sambungan Listrik

Sasayogian tanaga: The unit is dual voltage (120/277V). Connect the appropriate AC power supply wires to the fixture's input terminals as indicated in the wiring diagram.
Sambungan batré: Ensure the internal battery is properly connected after wiring the AC power. The battery is typically pre-connected but may require a final plug-in during installation.
Muatan Awal: After installation and power connection, allow the unit to charge for a minimum of 24 hours before conducting any tests. This ensures the nickel-cadmium battery reaches full capacity.

Lithonia Lighting EDG 1 R EL M6 LED Emergency Exit Sign, red letters, side view.

Gambar: Sisi view of the Lithonia Lighting EDG 1 R EL M6 LED Emergency Exit Sign, highlighting its slim profile and edge-lit design.

5. Parentah Operasi

The Lithonia Lighting EDG 1 R EL M6 operates automatically once properly installed and charged.

Operasi normal: When AC power is present, the LED 'EXIT' letters will be illuminated. The internal battery will continuously charge to maintain readiness for emergency operation.
Operasi Darurat: In the event of an AC power failure, the unit will automatically switch to battery power, illuminating the 'EXIT' letters for a minimum of 90 minutes.
Tombol tés: A test button is typically located on the side or bottom of the unit. Pressing this button simulates an AC power failure, allowing you to verify the emergency lighting function. The 'EXIT' letters should illuminate when the button is pressed and extinguish when released (assuming AC power is present).

Lithonia Lighting EDG 1 R EL M6 LED Emergency Exit Sign, red letters, front view.

Gambar: Hareupeun view of the Lithonia Lighting EDG 1 R EL M6 LED Emergency Exit Sign, clearly showing the red 'EXIT' letters.

6. Pangropéa

The EDG 1 R EL M6 is designed for low maintenance. However, regular checks are essential to ensure continued reliability.

Ujian Bulanan: Press the test button for at least 30 seconds to ensure the emergency lights operate.
Ujian taunan: Disconnect AC power to the unit for a full 90-minute discharge test. The unit should remain illuminated for the entire duration. Reconnect AC power after the test.
beberesih: Clean the exterior surfaces and acrylic panel with a soft, damp lawon. Ulah make cleaners abrasive atawa pangleyur. Pastikeun kakuatan dipegatkeun saméméh beberesih.
Ngagantian batré: The nickel-cadmium battery is maintenance-free and has a long lifespan. If the unit fails to hold a charge or operate for the required 90 minutes during testing, the battery may need replacement by qualified service personnel.
NFPA Compliance: All life safety equipment, including emergency lighting for paths of egress, must be maintained, serviced, and tested in accordance with all National Fire Protection Association (NFPA) and local codes.

7. Cara ngungkulan

If your EDG 1 R EL M6 LED Emergency Exit Sign is not functioning as expected, refer to the following common issues and solutions:

Masalah	Mungkin Cukang lantaranana	Solusi
'EXIT' letters do not illuminate during AC power failure.	Battery not charged or faulty; AC power not connected.	Ensure AC power is connected and allow 24 hours for initial charge. If problem persists, battery may need replacement.
'EXIT' letters do not illuminate when test button is pressed.	Battery not connected or faulty; unit not receiving AC power.	Verify AC power connection. Check battery connection. Allow 24 hours for charge.
Unit does not stay illuminated for 90 minutes during annual test.	Battery capacity reduced due to age or defect.	Battery needs replacement. Contact qualified service personnel.
'EXIT' letters are dim.	Low battery charge; dirty acrylic panel.	Allow unit to charge for 24 hours. Clean the acrylic panel.

For issues not listed above, or if troubleshooting steps do not resolve the problem, contact Lithonia Lighting customer support or a qualified electrician.

8. Spésifikasi

Detailed technical specifications for the Lithonia Lighting EDG 1 R EL M6 LED Emergency Exit Sign:

Jumlah modél: EDG 1 R EL M6
Nomer Bagian: LTHEDG1RELM6
Pabrikan: Lampu Lithonia
ukuran: Approximately 13 inches (Width) x 11.12 inches (Height)
Beurat barang: 2.2 pon (1 Kilogram)
warna: Red (letters)
Gaya: Batré-Powered
rengse: Brushed Aluminium
Bahan: Aluminum (housing), Acrylic (panel)
Sumber Daya: AC (for charging)
Voltage: 120/277V (Dual Voltage)
Wattage: 3 watt
Jenis bohlam: LED
Tipe Pamasangan: Surface Mount (Ceiling, Wall, End)
Sertifikasi: UL Didaptarkeun
Batré: Sealed, maintenance-free Nickel-Cadmium
Emergency Operation Duration: Minimum 90 menit
LED Lamp Kahirupan: Nepi ka 100,000 jam
Letter Height: 6 inci
Stroke Width: 3/4 inci
ViewJarak: 100 feet (UL 924 standard)

Lithonia Lighting EDG 1 R EL M6 LED Emergency Exit Sign with dimensions: 13 inches wide, 8 inches high.

Image: Lithonia Lighting EDG 1 R EL M6 LED Emergency Exit Sign with key dimensions indicated.

9. Garansi jeung Rojongan

For detailed warranty information, product registration, or technical support, please visit the official Lithonia Lighting websitus atanapi ngahubungan departemén layanan palanggan maranéhna. Simpen resi pameseran anjeun pikeun klaim jaminan.

Lithonia Lighting Customer Service: Refer to the contact information provided on the product packaging or the official brand websitus.

	Lithonia Lighting ELT Series Industrial Steel Emergency Lighting - Specifications and Ordering Detailed specifications, features, and ordering information for Lithonia Lighting's ELT16, ELT24, ELT36, and ELT50 Industrial Steel Emergency Lighting units. Includes electrical, battery, mounting details, and warranty information.
	Lampu Lithonia LRP / LRP2 LED Tepi-Lit Darurat Kaluar Tanda Instalasi sareng Pitunjuk Pangropéa Pamasangan komprehensif, pamariksaan, sareng pamaliharaan petunjuk pikeun Lithonia Lighting LRP/LRP2 Series 120/277V LED Edge-Lit Emergency Exit Signs, kalebet pilihan F, FA, sareng FI sareng flasher DC sareng fitur alarm anu tiasa didengar.
	Lithonia Lighting LED Combo Exit & Emergency Light Installation Instructions Comprehensive installation, operation, and maintenance guide for Lithonia Lighting's LED Combo Exit & Emergency Light, covering safety, mounting procedures, wiring, and battery backup.
	Lithonia Lighting ECBRM Quantum Running Man LED Light Bar Combo Unit - Emergency Lighting Specification Detailed specifications for the Lithonia Lighting ECBRM Quantum Running Man LED Light Bar Combo Unit, an emergency lighting fixture designed for path of egress illumination and marking. Includes features, construction, electrical, battery, installation, listings, warranty, ordering information, and spacing guidelines.
	Lithonia Lighting LED Combo Exit & Emergency Light Installation Instructions (EMCSA00802) Detailed installation instructions for the Lithonia Lighting LED Combo Exit & Emergency Light (Model EMCSA00802 Rev. F). Includes safety warnings, mounting procedures for back, top, and side installations, wiring diagrams, and operation details.
	Lithonia LED Combo Exit & Emergency Light Installation Instructions Comprehensive installation guide for the Lithonia LED Combo Exit & Emergency Light, covering safety warnings, installation procedures for various mounting types, operation details, maintenance, and wiring diagrams.