1. Bubuka
This manual provides essential information for the safe and correct installation, operation, and maintenance of your Legrand E14 Lamp Holder, model LEG91123. This product is designed for use with E14 screw-base bulbs, with a maximum wattage of 60W and operating at 230 Volts.
2. Émbaran Kasalametan
WARNING: Risk of electric shock. Always disconnect power at the main circuit breaker before installing or servicing electrical components.
- Installation should only be performed by a qualified electrician or competent person.
- Ensure the power supply is completely off before beginning any work.
- Ulah ngaleuwihan maksimum dipeunteun wattage of 60W for the connected bulb.
- Pastikeun sadaya sambungan aman sareng insulated leres.
- Produk ieu dirarancang pikeun dianggo di jero rohangan ngan di tempat anu garing.
3. Komponén produk
The Legrand E14 Lamp Holder consists of several parts designed for secure and reliable bulb connection.
Figure 3.1: Complete Legrand E14 Lamp Holder. This image shows the complete Legrand E14 lamp holder, featuring the threaded body for bulb insertion and the base for electrical connection.
Figure 3.2: Legrand E14 Lamp Holder disassembled. This image illustrates the main components of the Legrand E14 lamp holder, including the outer casing, internal mechanism, and shade ring.
- Luar Casing: Made of white polyamide material, providing insulation and protection.
- Mékanisme internal: Contains the electrical contacts and wiring terminals.
- Shade Ring: Used to secure a lampngiuhan ka lamp panyekel.
4. Parentah instalasi
Follow these steps for proper installation of the Legrand E14 Lamp Panyekel.
- Nyiapkeun Wiring: Ensure the power supply is disconnected. Strip approximately 8-10mm of insulation from the ends of the electrical wires.
- Terminal Aksés: Anu lamp holder's internal mechanism may need to be partially disassembled to access the wiring terminals. Refer to Figure 3.2 for component identification.
- Sambungkeun kawat: Insert the stripped wire ends into the designated terminals. The wire entry can be from the side or via a screw connection. Secure the wires firmly by tightening the terminal screws. Ensure no loose strands are present.
Figure 4.1: Internal wiring terminals. This image displays the internal wiring terminals of the Legrand E14 lamp holder, where electrical wires are connected.
- Pasang deui: Carefully reassemble the lamp holder components, ensuring all parts are correctly aligned and secured.
- Pamasangan: Anu lamp holder is designed for installation on a Ø10 male connector. Secure the lamp holder to the fixture using the appropriate mounting method.
- Attach Shade Ring (Optional): Lamun ngagunakeun alampshade, slide the shade ring over the threaded part of the lamp holder and tighten it to secure the lampngiuhan.
5. Operasi
Once installed, operating the lamp holder is straightforward:
- Selapkeun Bohlam: Gently screw an E14 screw-base bulb into the lamp wadahna dugi ka pageuh. Ulah kenceng teuing.
- Mulangkeun Daya: Turn on the power supply at the main circuit breaker.
- Tes: Activate the light switch to confirm proper operation.
6. Pangropéa
The Legrand E14 Lamp Holder requires minimal maintenance.
- beberesih: Disconnect power before cleaning. Wipe the exterior with a dry, soft cloth. Do not use abrasive cleaners or solvents.
- Pamariksaan: périodik mariksa lamp holder for any signs of damage, wear, or loose connections. If any issues are found, disconnect power and address them immediately.
- Ngagantian bohlam: Always disconnect power before replacing a bulb. Allow the old bulb to cool completely before removal.
7. Cara ngungkulan
Lamun sapatemon masalah sareng l Anjeunamp holder, refer to the following common problems and solutions:
| Masalah | Mungkin Cukang lantaranana | Solusi |
|---|---|---|
| Lampu teu hurung | Taya catu daya | Pariksa circuit breaker jeung switch témbok. |
| Lampu teu hurung | Bohlam salah | Replace the bulb with a new, working E14 bulb (max 60W). |
| Lampu teu hurung | Sambungan kabel leupas | Disconnect power and check all wire connections within the lamp holder. Tighten if necessary. |
| Cahya kedip-kedip | Bohlam leupas atawa sambungan | Ensure the bulb is screwed in tightly. Disconnect power and check wiring connections. |
8. Spésifikasi Téknis
- merek: Legrand
- Jumlah modél: LEG91123
- Jenis bohlam: E14 Screw-base
- Bahan: Polyamide-Imide
- warna: Bodas
- Voltage: 230 volt
- Daya maksimum: 60 Watt
- Ukuran produk (L x W x H): 3 x 3 x 6 cm
- beurat: 50 gram
- Tipe Pamasangan: For Ø10 male connector
- Spésifikasi anu saluyu: NF
- Negara asal: Cina
9. Garansi jeung Rojongan
For warranty information or technical support, please refer to the documentation provided with your purchase or contact Legrand customer service directly. Keep your proof of purchase for warranty claims.
