HP S2031 20-Inch Diagonal LCD Monitor User Manual

1. Bubuka

This manual provides essential information for the safe and efficient use of your HP S2031 20-Inch Diagonal LCD Monitor. Please read this guide thoroughly before operating the device to ensure proper setup, operation, and maintenance. Keep this manual for future reference.

2. Émbaran Kasalametan

• Salawasna simpen monitor dina permukaan anu rata sareng stabil supados henteu murag.
• Ulah ngahalangan liang ventilasi. Pastikeun aya rohangan anu cekap di sakitar monitor pikeun aliran hawa anu leres.
• Paké ngan kabel kakuatan jeung adaptor disadiakeun kalawan monitor.
• Hindarkeun ngalaan monitor ka lembab, hujan, atanapi suhu anu ekstrim.
• Disconnect the power cable from the wall outlet before cleaning or if the monitor will be unused for an extended period.
• Ulah nyobian ngalereskeun monitor sorangan. Rujukkeun sadaya perawatan ka petugas layanan anu mumpuni.

3. Eusi Paket

Pastikeun yén sadaya item aya dina bungkusan:

• HP S2031 20-Inch Diagonal LCD Monitor
• Stand Monitor (Dasar sareng Beuheung)
• Kabel listrik
• VGA Kabel
• DVI-D Cable (may vary by region)
• Documentation (Quick Setup Guide, Warranty Information)

4. Setélan

4.1 Ngarakit Stand Monitor

1. Place the monitor face down on a soft, clean cloth to prevent scratching the screen.
2. Attach the stand neck to the back of the monitor by aligning the tabs and pushing firmly until it clicks into place.
3. Attach the stand base to the bottom of the stand neck. Secure it with the captive screw located on the underside of the base.
4. Carefully lift the monitor and place it upright on a stable surface.

4.2 Nyambungkeun Kabel

Tingal gambar di handap pikeun lokasi port.

Gambar: Tukangeun view of the HP S2031 monitor, showing the power input, VGA port, and DVI-D port.

1. Sambungkeun kabel video: Connect one end of the VGA or DVI-D cable to the corresponding port on the back of the monitor. Connect the other end to the video output port on your computer. For optimal digital quality, use the DVI-D connection.
2. Sambungkeun Kabel Daya: Plug the power cord into the monitor's power input, then plug the other end into a grounded electrical outlet.

4.3 Mimiti Power-On

Press the power button on the front or bottom bezel of the monitor. The power indicator light should illuminate, and the HP logo or your computer's display should appear on the screen.

5. Ngoperasikeun Monitor

5.1 Daya Hurung/Pareuman

Press the power button (usually located on the lower right bezel) to turn the monitor on or off. The power indicator light will show the monitor's status (e.g., green for on, amber for standby).

5.2 Napigasi Menu dina Layar (OSD).

The OSD menu allows you to adjust various monitor settings. Buttons for OSD navigation are typically located on the bottom bezel.

• Pencét éta ménu button to open the OSD menu.
• Ngagunakeun éta Luhur/Turun or Kénca/Katuhu tombol panah pikeun nganapigasi pilihan menu.
• Pencét éta Pilih or OK button to enter a sub-menu or confirm a selection.
• Pencét éta Kaluar or ménu button again to close the OSD menu.

5.3 Nyaluyukeun Setélan

Setélan OSD umum ngawengku:

• Caang/Kontras: Saluyukeun luminance sadayana sareng bédana antara daérah terang sareng poék.
• Kontrol Warna: Robah suhu warna, tingkat RGB, atanapi pilih modeu warna prasetél.
• Kontrol Gambar: Fine-tune sharpness, clock, phase, and horizontal/vertical position (primarily for analog VGA input).
• Pilih Input: Manually switch between VGA and DVI-D inputs.
• Manajemén: Access power-saving options, OSD timeout, and factory reset.

6. Pangropéa

6.1 Ngabersihan Monitor

• Salawasna cabut monitor tina stop kontak sateuacan beberesih.
• For the screen: Gently wipe with a soft, lint-free cloth. For stubborn marks, lightly dampBilas lawon ku cai atanapi pembersih layar anu henteu ngandung amonia sareng henteu ngandung alkohol. Ulah nyemprotkeun pembersih langsung kana layar.
• Pikeun casing: Use a soft, dry cloth to wipe dust.
• Ulah nganggo pembersih abrasif, lilin, atanapi pangleyur sabab tiasa ngaruksak permukaan monitor.

6.2 Perawatan Umum

• Ulah neundeun barang beurat dina monitor atawa kabelna.
• Avoid exposing the monitor to direct sunlight or heat sources.
• If moving the monitor, ensure it is properly disconnected and handled carefully to prevent damage.

7. Cara ngungkulan

7.1 Taya Gambar dina Layar

• Pastikeun kabel daya disambungkeun pageuh kana monitor sareng kana stop kontak listrik.
• Check that the video cable (VGA or DVI-D) is firmly connected to both the monitor and the computer.
• Verify that the monitor is powered on (check the power indicator light).
• Pencét éta Pilih Input button on the monitor to ensure the correct input source (VGA or DVI-D) is selected.
• Balikan deui komputer anjeun.

7.2 Gambar Burem atanapi Distorsi

• Ensure the monitor's resolution is set to its native resolution of 1600 x 900 pixels in your computer's display settings.
• If using a VGA connection, run the OSD's Otomatis Saluyukeun function to optimize the image.
• Pariksa kabel vidéo pikeun karuksakan atawa sambungan leupas.
• Saluyukeun Jam jeung Fase settings in the OSD menu (for VGA input).

7.3 Power Indicator Light is Off

• Confirm the power cable is fully inserted into the monitor and the wall outlet.
• Uji stop kontak listrik nganggo alat anu sanés pikeun mastikeun éta tiasa dianggo.
• If using a power strip or surge protector, ensure it is switched on.

8. Spésifikasi

9. Garansi jeung Rojongan

Your HP S2031 monitor is covered by a limited warranty. Please refer to the warranty documentation included with your product for specific terms and conditions. For technical support, driver downloads, or further assistance, please visit the official HP support websitus atanapi hubungi layanan palanggan HP.

Note: Warranty terms may vary by region and purchase date. Proof of purchase may be required for warranty claims.