1. Bubuka
Thank you for choosing the Fischer Thermax 10/160 M6 Distance Mounting System. This system is designed for secure and thermally optimized fastening of light to medium loads to external walls with thermal insulation composite systems (ETICS).
The Thermax system ensures a reliable connection without creating thermal bridges, making it an energy-efficient solution for various applications. Please read this manual carefully before installation to ensure proper and safe use of the product.
2. Émbaran Kasalametan
Always observe general safety regulations and local building codes during installation. Failure to follow these instructions may result in injury or damage to property.
- Anggo alat pelindung pribadi (PPE) anu cocog, kalebet kacamata kaamanan, sarung tangan, sareng panyalindungan dédéngéan.
- Pastikeun wewengkon gawé téh well-cahayana sarta bébas tina halangan.
- Verify the type and condition of the building material before drilling.
- Do not overload the installed fixture beyond the specified load capacities.
- Jauhkeun barudak sareng jalma anu henteu sah ti daérah padamelan.
- Upami teu yakin kana léngkah naon waé, konsultasi ka ahli anu mumpuni.
3. Komponén produk
The Fischer Thermax 10/160 M6 system includes the following main components:
- Thermax Double-Threaded Screw: The core component, designed to mill through plaster and insulation.
- Anti-Cold Cone: A glass-fiber reinforced plastic cone that interrupts the thermal bridge.
- UX Universal Anchor: For secure anchoring in various building materials.
- SX Anchor: (Included in some kits, check packaging)
- Caps: For finishing the installation.
Gambar 3.1: Leuwihview of the Fischer Thermax 10/160 M6 system components, including the main screw, plastic cone, and two types of anchors.
4. Setup jeung Instalasi
Follow these steps for proper installation of the Fischer Thermax 10/160 M6 system:
- Prepare the Mounting Point:
Identify the desired mounting location. Drill a hole through the insulation and into the base material (e.g., concrete, masonry) using an appropriate drill bit. The drill diameter and depth depend on the anchor type and base material. For the UX 12x70 anchor, a 12mm drill bit is typically used.
Figure 4.1: Drilling the pilot hole for the Thermax system.
- Selapkeun Jangkar:
Insert the UX universal anchor into the drilled hole until it is flush with the base material behind the insulation. Ensure a snug fit.
- Install the Thermax Screw:
Place the anti-cold cone onto the double-threaded screw. Drive the double-threaded screw through the insulation and into the anchor using a suitable driver (e.g., a hex bit or wrench). The screw's self-milling feature will cut through the plaster and insulation. Continue turning until the anti-cold cone is firmly seated against the insulation surface.
Figure 4.2: Driving the Thermax screw into the pre-drilled hole and anchor.
- Pasangkeun Perlengkapan:
Once the Thermax screw is securely installed, you can attach your fixture (e.g., light, mailbox, sign) to the exposed threaded end of the screw. Use appropriate nuts and washers to secure the fixture firmly.
Figure 4.3: Attaching the external fixture to the Thermax screw.
- Apply Finishing Cap (Optional):
If included in your kit, place the finishing cap over the exposed nut for a clean aesthetic and added protection.
Figure 4.4: Applying the finishing cap.
Pamasangan Examples:
Example 1: Mounting an outdoor light fixture.
Example 2: Mounting a pipe bracket.
Example 3: Mounting a satellite dish or antenna.
Example 4: Mounting a larger pipe or conduit.
5. Parentah Operasi
The Fischer Thermax 10/160 M6 is a passive mounting system. Once installed, its primary function is to securely hold the attached fixture while minimizing thermal bridging. There are no active "operating" steps for the system itself.
Ensure that the attached fixture is within the load limits specified for the Thermax system and the base material. Regularly inspect the fixture and the mounting point for any signs of loosening or damage, especially after extreme weather conditions.
6. Pangropéa
The Fischer Thermax system requires minimal maintenance. However, periodic inspection is recommended to ensure long-term stability and safety.
- Inspeksi Visual: Periodically check the mounted fixture and the Thermax connection point for any visible signs of wear, corrosion, cracks, or loosening.
- Pariksa tightness: If accessible and safe to do so, gently check the tightness of the nuts securing the fixture. Do not overtighten.
- beberesih: Keep the area around the mounting point clean from debris that might accumulate.
- Ruksakna: If any damage is observed, consult a professional for assessment and repair. Do not attempt to repair damaged components yourself.
7. Cara ngungkulan
Bagian ieu ngabahas masalah umum anu tiasa timbul nalika atanapi saatos pamasangan.
| Masalah | Mungkin Cukang lantaranana | Solusi |
|---|---|---|
| Screw does not engage anchor. | Incorrect drill hole diameter or depth; anchor not fully seated; wrong anchor type for base material. | Verify drill bit size and depth. Ensure anchor is fully inserted. Use the correct anchor for your specific base material. |
| Fixture feels loose after installation. | Insufficient tightening; anchor failure; base material damage. | Ensure nuts are tightened to recommended torque (if specified). Re-evaluate base material integrity. If anchor failed, consider re-drilling in a new location or using a larger anchor/system if appropriate. |
| Thermal bridge still present. | Anti-cold cone not properly seated against insulation. | Ensure the anti-cold cone is flush and tightly seated against the insulation surface. |
Upami anjeun mendakan masalah anu henteu didaptarkeun di dieu atanapi upami solusi henteu ngabéréskeun masalah, mangga ngahubungi dukungan palanggan.
8. Spésifikasi
| Atribut | Rincian |
|---|---|
| Modél | Thermax 10/160 M6 |
| Produsén Bagian Jumlah | 45695 |
| merek | Fischer |
| Ukuran | 10/160 |
| Gaya | M6 |
| Bahan | Metal (screw), Plastic (cone, anchors) |
| Kuantitas per pak | 20 pieces (Thermax, UX 12x70, SX 5x25, caps) |
| Drill Diameter (for UX 12x70) | 12 Millimeters (approx.) |
| Aplikasi | Fixing light to medium loads in ETICS (External Thermal Insulation Composite Systems) |
| Suitable Base Materials | Concrete, perforated brick, light concrete hollow block, sand-lime perforated stone, masonry brick, aerated concrete, wood. |
9. Garansi jeung Rojongan
Fischer products are manufactured to high-quality standards. For specific warranty information, please refer to the documentation provided with your purchase or visit the official Fischer websitus.
For technical support, questions regarding installation, or to report any issues, please contact Fischer customer service. Contact details can typically be found on the product packaging or the manufacturer's official websitus.
Websitus: www.fischer.group
