AeroCool X-Blaster 80mm Fan Instruction Manual

1. Bubuka

Thank you for choosing the AeroCool X-Blaster 80mm high-speed fan. This fan is designed to provide efficient cooling for your computer system, featuring a durable 2-ball bearing design for extended lifespan and stable performance. This manual provides essential information for proper installation, operation, and maintenance to ensure optimal performance and longevity of your fan.

Image 1.1: The AeroCool X-Blaster 80mm fan, featuring clear fan blades and a black frame.

2. Émbaran Kasalametan

• Salawasna pegatkeun daya tina komputer anjeun sateuacan masang atanapi ngalaksanakeun pangropéa dina komponén internal naon waé.
• Cekel kipas ku pigurana supados bilahna henteu ngaruksak atanapi komponén internalna.
• Ensure proper ventilation during operation to prevent overheating of other components.
• Jauhkeun tina jangkauan barudak.
• Do not attempt to modify the fan or its wiring, as this may void the warranty and pose a safety risk.

3. Eusi Paket

Pastikeun yén sadaya item aya dina bungkusan:

• 1x AeroCool X-Blaster 80mm Fan
• 1x 3-pin to 4-pin Molex Converter Cable
• 4x Pasang Sekrup

Image 3.1: Contents of the AeroCool X-Blaster 80mm fan package, including the fan, converter cable, and screws.

4. Setup jeung Instalasi

1. Nyiapkeun sistem anjeun: Power off your computer and disconnect it from the main power supply. Open your computer case to access the internal components.
2. Nangtukeun lokasi pamasangan: Locate an available 80mm fan mounting point within your computer case. Common locations include the rear, front, or side panels.
3. Determine airflow direction: Fans typically have an arrow on the side indicating the direction of airflow. Install the fan to push air in the desired direction (e.g., exhaust air out of the case or intake air into the case).
4. Pasang kipas: Position the fan over the mounting holes. Use the four provided mounting screws to secure the fan to the case. Do not overtighten the screws.
5. Nyambungkeun kakuatan:
   • 3-pin connection: Connect the fan's 3-pin connector directly to an available 3-pin fan header on your motherboard. This allows for RPM monitoring and potential speed control via BIOS/UEFI or software.
   • 4-pin Molex connection: If no 3-pin motherboard header is available, use the included 3-pin to 4-pin Molex converter cable. Connect the fan's 3-pin connector to the converter, then connect the 4-pin Molex connector to an available Molex power connector from your power supply. Note that using the Molex connector will typically run the fan at full speed without RPM monitoring or speed control.
6. Tutup kasusna: Once the fan is securely mounted and connected, close your computer case and reconnect the power supply.

Image 4.1: The AeroCool X-Blaster 80mm fan showing its 3-pin power connector, ready for installation.

5. Parentah Operasi

After successful installation, power on your computer. The AeroCool X-Blaster 80mm fan will begin operating immediately. If connected to a motherboard 3-pin header, its speed may be regulated by your system's BIOS/UEFI settings or fan control software. If connected via the 4-pin Molex adapter, the fan will operate at its maximum speed of 4000 RPM, providing an airflow of up to 53 CFM.

Monitor your system's temperatures to ensure adequate cooling. The fan is designed for continuous operation to maintain optimal internal case temperatures.

6. Pangropéa

Regular maintenance helps ensure the longevity and efficiency of your fan:

• Ngaleungitkeun lebu: Periodically (e.g., every 3-6 months), power off your computer and disconnect it from power. Open the case and use compressed air or a soft brush to gently remove dust accumulation from the fan blades and frame. Hold the fan blades stationary while cleaning with compressed air to prevent over-spinning the bearings.
• Pamariksaan: Visually inspect the fan for any signs of damage, loose wires, or obstructions. Ensure the fan spins freely without resistance.
• Bearing Noise: While the 2-ball bearing design offers durability, excessive or unusual noise may indicate wear. If the fan becomes significantly louder or produces grinding sounds, consider replacement.

7. Cara ngungkulan

• Kipas teu berputar:
  • Ensure the power cable is securely connected to either the motherboard header or the Molex power supply.
  • Verify that your computer's power supply is functioning correctly.
  • Check BIOS/UEFI settings if connected to a motherboard header; some settings might disable fan headers or set very low RPMs.
• Noise kaleuleuwihan:
  • The AeroCool X-Blaster is a high-speed fan (4000 RPM) and will generate a noticeable noise level (rated at 46 dBA). This is normal for its performance characteristics.
  • Check for obstructions (e.g., cables) hitting the fan blades.
  • Pastikeun kipas dipasang sacara aman sareng henteu ngageter kana wadahna.
  • If connected to a motherboard header, try adjusting fan speed settings in BIOS/UEFI or fan control software to a lower RPM if cooling requirements allow.
• Insufficient airflow:
  • Verify the fan is installed with the correct airflow direction for your case's cooling strategy.
  • Clean any dust buildup on the fan blades or case vents.

8. Spésifikasi

9. Garansi jeung Rojongan

For warranty information or technical support, please refer to the official AeroCool websitus atanapi ngahubungan pangecér Anjeun. Simpen bukti pameseran anjeun pikeun klaim garansi.

Resmi AeroCool Websitus: www.aerocool.com.tw