1. Bubuka
This manual provides instructions for the Universal 3-Button 433.92MHz Garage Door Remote Control. This device is designed to clone existing garage door remotes, offering a convenient solution for controlling multiple garage door openers with a single unit. It supports various encoding methods including rolling code, fixed code, and learning code, making it compatible with a wide range of garage door systems.
Fitur konci:
- Compatible with a wide range of 433.92MHz remote controls.
- Supports secure encryption protocols (rolling code, fixed code, learning code).
- Capable of controlling up to three different garage door openers, even from different brands.
- Features an LED indicator for operational feedback.
- Includes a visor clip for convenient in-car storage.
2. Eusi Paket
Mangga parios pakét kanggo barang-barang ieu:
- 1 x Universal 3-Button Garage Door Remote Control
- 1 x CR2032 Battery (pre-installed or included separately)
- 1 x Garage Door Visor Clip
- 1 x Gantungan Kunci
- 1 x English Instruction Card (detailed instructions for cloning)
3. Spésifikasi
| Atribut | Nilai |
|---|---|
| Frékuénsi | 433.92MHz |
| Kancing | 3 |
| Métode Encoding | Rolling code, Fixed code, Learning code |
| Jenis Batré | CR2032 (kaasup) |
| Sertifikasi | CE |
| Asalna | Daratan Cina |
4. Kasaluyuan
This remote control is designed for use with garage door openers operating at a frequency of 433.92MHz. It is compatible with a wide range of models, including but not limited to:
- MuTAN-II N1, N2, N4, N2 Mini
- MUTANcode T1 TX1, T2 TX2, T4 TX4, T2 TX2 Mini
- MASTERcode CLEMSA MV1, MV12, MV123
Catetan penting:
- Ensure your original remote operates at 433.92MHz. This remote is NOT compatible with 868MHz systems.
- The appearance of your original remote should match the compatible models shown in the product images for best results.
5. Setup: Cloning Your Original Remote Control
This remote control is a cloning device, meaning it learns the signal from your existing remote. The cloning process requires your original remote control to be present.
Cloning Procedure:
- **Clear Existing Codes (First Use Recommended):**
- Press and hold the two top buttons (Button 1 and Button 2) on the new remote simultaneously until the LED indicator flashes rapidly (approximately 3 seconds).
- Release both buttons. The LED should flash briefly, indicating that the memory has been cleared.
- **Initiate Cloning:**
- Place your original remote control and the new remote control side-by-side, as close as possible.
- Press and hold the button on your original remote that you wish to clone. The LED on the original remote should illuminate.
- While still holding the button on the original remote, press and hold the corresponding button on the new remote that you want to program. The LED on the new remote will first flash slowly, then rapidly.
- Once the LED on the new remote flashes rapidly and continuously, release both buttons. This indicates successful cloning of that button.
- **Repeat for Additional Buttons:** Repeat step 2 for any other buttons you wish to program on the new remote (up to three different functions).
Post-Cloning Activation (for Rolling Code Systems):
If your original remote uses a kode dibereskeun system, the new remote should work immediately after cloning. However, if your original remote uses a rolling code system, an additional activation step is required on your garage door opener's receiver:
- Locate the "Learn" or "Program" button on your garage door opener's motor unit (usually found near the wiring terminals or antenna).
- Press and release the "Learn" or "Program" button. The indicator light on the opener will usually illuminate or flash, indicating it's in learning mode.
- Within 30 seconds, press the newly cloned button on your new remote control. The opener's light may flash or click, confirming that the remote has been successfully programmed to the receiver.
- Nguji kadali jauh.
Refer to your garage door opener's manual for specific instructions on how to put it into learning mode.
6. Parentah Operasi
Once successfully programmed, operating the remote control is straightforward:
- Opening/Closing Garage Door: Press the programmed button corresponding to the desired garage door. The LED indicator on the remote will illuminate during transmission.
- Controlling Multiple Doors: Each of the three buttons can be programmed to control a different garage door opener.
7. Pangropéa
Ngagantian batré:
The remote control uses a CR2032 coin cell battery. If the LED indicator does not light up or the remote's range decreases significantly, it's time to replace the battery.
- Buka remot kontrol kalayan ati-atiasing.
- Leupaskeun batré CR2032 heubeul.
- Insert a new CR2032 battery, ensuring correct polarity (+ side up).
- Close the remote control casing aman.
Buang batré heubeul kalawan tanggung jawab nurutkeun peraturan lokal.
8. Cara ngungkulan
| Masalah | Mungkin Cukang lantaranana | Solusi |
|---|---|---|
| Remote does not clone. |
|
|
| Remote cloned but garage door doesn't open. |
|
|
| LED teu hurung. | Batré maot. | Ganti batré CR2032. |
9. Tips pamaké
- For optimal cloning success, ensure both remotes have fresh batteries and are held very close during the cloning process.
- If you have multiple garage door openers, consider programming each button on this universal remote to a different opener for consolidated control.
- Always test the cloned remote from various distances and angles after programming to ensure reliable operation.
10. Garansi jeung Rojongan
For any issues or questions regarding your Universal 3-Button 433.92MHz Garage Door Remote Control, please refer to the included instruction card or contact the seller for assistance. Keep your purchase records for warranty claims.
