1. Bubuka
Hatur nuhun pikeun meuliasing the AOC AM500MAX Ergonomic Monitor Arm. This manual provides detailed instructions for safe and efficient installation, operation, and maintenance of your new monitor arm. Please read this manual thoroughly before beginning installation to ensure proper setup and to prevent potential damage or injury.
2. Émbaran Kasalametan
- PERHATOSAN: Do not exceed the stated maximum load (4-12kg), otherwise equipment damage or personal injuries may occur.
- PERHATOSAN: Ensure the mounting surface can safely support the combined weight of the monitor arm, all accessories, and the monitor.
- PERHATOSAN: This product contains small parts. Keep small parts out of the reach of children.
- PERHATOSAN: Nalika nganggo clamp mounting method, do not rotate the monitor until it is clear of the desk surface to prevent tipping and falling.
- PERHATOSAN: Ensure sufficient cable slack to allow movement in all directions, otherwise equipment damage or personal injuries may result.
- PERHATOSAN: When adjusting the monitor position, ensure the monitor is firmly mounted.
- PERHATOSAN: Remove the monitor before removing the arm, otherwise equipment damage or personal injuries may result.
- PERHATOSAN: Saméméh unmounting monitor, pindahkeun panangan ka posisi pangluhurna pikeun nempatkeun spring panangan kana kaayaan énergi panghandapna, disebutkeun tatu pribadi serius atawa karuksakan alat bisa lumangsung.
- PERHATOSAN: This product contains a powerful spring. Do not disassemble this product without authorization, otherwise serious personal injury or equipment damage may occur.
3. Eusi Paket
Sateuacan masang panangan monitor, mangga pastikeun sadaya asesoris dina kaayaan anu saé. Upami aya asesoris anu leungit atanapi ruksak, mangga ngahubungi distributor lokal anjeun.
Daptar bagian produk:
- Dasar Clamp assembly (A) - 1
- Lower arm (B) - 1
- Upper arm (C) - 1
- Head (D) - 1
Product Accessory List:
- Bolt M4x12 (a) - 4
- Allen key 4mm (b) - 1
- Grommet Plate (c) - 1
- Spacer 9x5.4x4 (d) - 4
- Spacer 9x5.4x16 (e) - 4
- Bolt M4x25 (f) - 4
- Wingnut (g) - 1
- Grommet Screw (h) - 1
4. Spésifikasi
| Fitur | Spésifikasi |
|---|---|
| Modél | AM500 MAX |
| Ukuran Monitor | 27-40 inci |
| Kapasitas nanggung beban | 4-12 kg |
| VESA liang pitch | 75x75mm / 100x100mm |
| Max Extension | 455 mm |
| Bracket Arm Height | 500 mm |
| Rentang Angkat | 250 mm |
| Sudut Dengdekkeun | -15 ° ka +90 ° |
| Swivel Range (Left/Right) | ± 90° |
| Rotasi layar | 360° |
| Desktop ClampKetebalan | 15-90 mm |
| Desktop Drilling Thickness (Grommet) | 15-90 mm |
| Drill Diameter (Grommet) | 10-60 mm |
| Beurat bersih | 2.8 kg |
| Beurat kotor | 3.2 kg |
| Ukuran Bungkusan | 415(L) x 190(W) x 139(H) mm |
Pikeun visual leuwihview of the product dimensions, refer to the image below:
5. Setup jeung Instalasi
Métode pamasangan:
The AOC AM500MAX monitor arm supports two primary installation methods:
- Fixture Installation (Clamp Tipe): This method is suitable for desktop thicknesses between 15-90mm.
- Perforated Installation (Grommet Type): This method requires a desktop aperture greater than 10mm and is suitable for desktop thicknesses between 15-90mm.
Léngkah-léngkah pamasangan:
- Install Monitor Bracket: Attach the mounting bracket (D) to the monitor using the M4x12 bolts (a). Tighten the screws by hand. Ensure the VESA holes on your monitor are 75x75mm or 100x100mm.
- Mount Lower Arm: Insert the lower arm (B) onto the desk mounting bracket (A). Ensure it is fully seated.
- Install Upper Arm: Insert the upper arm (C) onto the lower arm (B). Ensure it is fully seated.
- Pasang Monitor: Carefully attach the monitor by inserting the monitor bracket onto the upper arm mount.
- Manajemén Kabel: Route the monitor's power and data cables through the integrated cable tray. Ensure there is sufficient cable slack to allow for full range of motion without strain. This arm can accommodate 2 cables with a 6mm diameter or 3 cables with a 3mm diameter.
Bracket Selection Guide and Common Installation Issues:
- Kasaluyuan VESA: Ensure your monitor has 75x75mm or 100x100mm VESA holes.
- Unsuitable Desktop Types: Avoid installing on fragile desktops (e.g., marble, glass), desktops with crossbeams/baffles that reduce clamping surface, or desktops with anomalies/inclined edges. Do not install upside down, use suspended side clamps, or reverse the arm's orientation.
- Monitor Back Sunken: If your monitor has a concave design on the back, use the bracket accessory kit with 25mm extension screws. The installation sequence should be: monitor > isolation column > head > long screw.
- Hand Screw Too Long: If an installation screw is too long, use the provided washer (4mm gasket) on the screw.
6. Operasi sareng Pangaluyuan
Penyesuaian Tegangan Spring:
To adjust the spring tension, first position the arm to a 90° angle. Use the Allen key (b) to adjust the screw:
- Tighten (+): Increase spring tension if the monitor is too heavy or does not hover freely.
- Loosen (-): Decrease spring tension if the monitor is too light or does not hover freely.
Multiple adjustments may be required to achieve the desired free-hovering effect. Do not completely unscrew the adjustment screws.
Penyesuaian Rotasi:
To adjust the rotation friction, use the Allen key (b) on the designated screw:
- Tighten (+): Increase friction if the arm rotates too easily.
- Loosen (-): Decrease friction if the arm is too stiff to rotate.
Do not completely unscrew the adjustment screws.
Display Angle (Tilt) Adjustment:
To adjust the display's tilt angle, use the Allen key (b) on the tilt mechanism:
- Turn clockwise (+): Increase friction to fix the display angle more securely.
- Turn counter-clockwise (-): Reduce friction to make the display more flexible for tilting.
Do not completely unscrew the adjustment screws.
Video Demonstrasi:
Watch this video for a visual guide on the features and adjustments of the AOC AM500MAX monitor arm:
This video demonstrates the features and adjustability of the AOC AM500MAX monitor arm, showcasing its load-bearing capacity, smooth movement, and dual installation options.
7. Pangropéa
Regularly check whether the fixing screws are tight to ensure stability and safety. Clean the monitor arm with a soft, dry cloth. Avoid using abrasive cleaners or solvents.
8. Cara ngungkulan
- Monitor Sinks/Doesn't Stay Up: Adjust spring tension by tightening the screw (b) clockwise.
- Monitor Floats/Doesn't Stay Down: Adjust spring tension by loosening the screw (b) counter-clockwise.
- Arm Rotates Too Easily/Stiffly: Adjust the rotation screw (b) to increase or decrease friction as needed.
- Monitor Tilts Too Easily/Stiffly: Adjust the tilt screw (b) to increase or decrease friction as needed.
- Cables Snagging: Ensure cables are routed correctly through the cable management system and have enough slack for full arm movement.
9. Tips pamaké
For optimal ergonomic benefits, adjust your monitor arm so that the top of your screen is at or slightly below eye level when you are sitting comfortably. Experiment with different positions to find what works best for your posture and workflow. The arm's wide range of motion allows for versatile screen positioning, including portrait mode, which can be beneficial for coding or document review.
10. Jaminan & Dukungan
This product comes with a 5-year warranty, ensuring long-term reliability and peace of mind.
For detailed information and further assistance, please refer to the official user manual PDF available at: AOC AM500MAX User Manual (PDF).
