Buku Panduan Pangguna Duplikator Kontrol Jarak Jauh Multi-Frékuénsi GGBEE M9

Bubuka

This manual provides detailed instructions for the GGBEE M9 Multi-Frequency Remote Control Duplicator. This device is designed to copy fixed code remote controls for various applications, including garage doors and gate key fobs, operating within the 300-980MHz frequency range. Please read this manual thoroughly before use to ensure proper operation and to maximize the lifespan of your device.

spésifikasi

Disetél

Before using your M9 remote control duplicator, ensure it is adequately charged via the 5V TPC-C interface. The device is ready for operation once charged.

Initial Clearing of Existing Codes

1. Press button 1 and button 2 simultaneously.
2. Hold both buttons for approximately 2 seconds until the LED indicator flashes.
3. Release both buttons. The LED should continue to flash rapidly.
4. After clearing, press any key on the remote. The indicator light should flash and then turn off, confirming successful code clearing.

Catetan:

• The indicator light must keep flashing before you release your hand.
• If the LED does not flash for a long time, it indicates that the two buttons were not pressed simultaneously. Repeat the operation.

Parentah Operasi

Copying Codes

To copy a code from an existing remote control to your M9 duplicator:

1. Place your original remote control and the M9 duplicator side-by-side.
2. Simultaneously press the desired button on your original remote and the corresponding button on the M9 duplicator (you can choose which button on the M9 to assign).
3. Hold both buttons until the channel number on the M9's display tube remains constantly lit. This indicates a successful copy for that button.
4. Repeat this process for any other keys you wish to copy.

Catetan:

• Do not release the buttons on either remote control during the copying process until the display tube number on the M9 duplicator is continuously lit.

Restoring Accidentally Cleared Codes

If you accidentally clear the codes from your M9 duplicator, you can restore them:

1. Simultaneously press the bottom two keys on the M9 remote control.
2. Hold for 2 seconds until the LED lights flash quickly.
3. Leupaskeun leungeun anjeun.
4. Press any key on the remote after recovery; the key's indicator should remain constantly lit, confirming restoration.

Ngonci Saluran

The M9 remote control features a channel locking function to prevent accidental switching:

1. To lock a channel, simultaneously press the second button in the first row and the first button in the middle row.
2. If the LED light flashes quickly, the channel is successfully locked. Once locked, switching channels is not allowed.
3. To cancel the channel lock, repeat the same procedure.

Pamérésan masalah

• LED does not flash during clearing: Ensure you are pressing both designated buttons (button 1 and button 2) simultaneously and holding them for the required 2 seconds. Repeat the process carefully.
• Copying fails (channel number does not stay lit):
  • Ensure both the original remote and the M9 duplicator are held close together during the copying process.
  • Verify that you are holding both the original remote's button and the M9's target button simultaneously without releasing until the M9's display confirms success.
  • Confirm that your original remote uses a fixed code, as this duplicator is designed for fixed code systems.
  • Check the battery level of both remotes.
• Remote control distance is shorter than expected:
  • Ensure the M9 duplicator is fully charged.
  • Check for any obstructions between the remote and the receiver.
  • Environmental factors or interference can affect range.
• Channel locking not working: Ensure you are pressing the correct combination of buttons (second button in the first row and first button in the middle row) simultaneously until the LED flashes quickly.

Tip pamaké

• For best copying results, perform the copying procedure in a quiet area away from other radio frequency interference.
• Always clear the M9 duplicator's memory before attempting to copy new codes to prevent conflicts.
• Keep the M9 duplicator charged to ensure optimal performance and range.
• Label your copied buttons if you are duplicating multiple different remotes to avoid confusion.

Garansi sareng Rojongan

The GGBEE M9 Multi-Frequency Remote Control Duplicator is designed for reliability and ease of use. For any technical support or warranty inquiries, please contact your retailer or the manufacturer directly. Keep your proof of purchase for warranty claims.

For further assistance, please refer to the official product support channels provided by GGBEE Intelligent Home Store.