1. Bubuka
This manual provides detailed instructions for the setup, programming, operation, and maintenance of your Yinuogo remote control for garage doors and gate openers. Please read this manual carefully before use to ensure proper functionality and longevity of your device.
The Yinuogo remote controls are designed for convenience and security, utilizing rolling code technology for reliable operation.
2. Spésifikasi
| Atribut | Rincian |
|---|---|
| Ngaran Brand | Yinuogo |
| Nomer modél | YNG123, YNG300, YNG814 |
| Métode Encoding | Rolling Code (Programming with the receiver) |
| Frékuénsi | 433.92MHz |
| Kancing | 2 or 4 (depending on model) |
| Rentang | 50/100m (approximate) |
| Batré | 6V (2x CR2016) - Included |
| Asalna | Daratan Cina |
| Sertifikasi | CE, FCC, RoHS, WEEE |
| Kimia anu prihatin tinggi | Euweuh |
3. Model cocog
These remote controls are compatible with a range of garage door and gate openers. Please ensure you have access to your receiver/opener for programming before purchase.
- MITTO 2
- MITTO 4
- MITTO2A
- MITTO4A
- MITTO2M
- MITTO4M
- KLEIO B RCA 02
- KLEIO B RCA 04
- MITTO B RCB 02
- MITTO B RCB 04
- TRC1 TRC2 TRC4
4. Setelan sareng Pemrograman
Programming your new remote control requires access to your receiver. There are typically two main types of programming procedures:
Type 1 Programming (using SW1/SW2 buttons on receiver)
- Buka casing of your receiver. It is usually located next to your motor.
- On the receiver circuit board, press the programming button (SW1). The LED light of the receiver will blink. Release the button.
- Press both buttons on your new remote control at the same time. Release them. The LED light of the receiver should remain lit fixedly.
- Press the left button on your new remote control. Release it. The LED light of the receiver will blink.
- Wait 5 seconds. The LED light of the receiver will turn off.
- Repeat this procedure for the right button of your new remote control. This time, use the programming button SW2 on the receiver.
- Antosan 10 detik.
- Your new remote control is programmed.
Type 2 Programming (using 'OK' and '-' buttons on receiver)
- Press the “OK” button on your receiver twice. The screen will display “PARA.”
- Press the “-” button on your receiver twice. The screen will display “RADIO.”
- Press the “OK” button on your receiver once. The screen will display “ADI STRT.”
- Press the “OK” button on your receiver once. The screen will display “Hidden Button.”
- Press both buttons on your new remote control at the same time. Keep them pressed down. The screen will display “Released”.
- Let the buttons go. The screen will display “Desired Button”.
- Press a button on your new remote control. The screen will display “OK”.
- Antosan 10 detik.
- Your new remote control is programmed.
Programming Demonstration Video
5. Parentah Operasi
Once programmed, your remote control is ready for use. Simply press the corresponding button on the remote to activate your garage door or gate opener. Ensure you are within the operational range of the receiver for reliable performance.
6. Pangropéa
Ngagantian batré
A decrease in the remote control's operational range or a flashing LED indicator suggests that the batteries are low and need to be replaced. The remote uses two CR2016 6V batteries.
- When the LED of the transmitter flashes, it indicates that the batteries are low and must be replaced.
- Ensure the battery terminals are not short-circuited or touched with bare hands during replacement.
Perawatan Umum
- Jaga remot kontrol tetep garing sareng jauh tina suhu anu ekstrim.
- Hindarkeun leupaskeun kadali jauh atanapi tunduk kana tabrakan anu kuat.
- Bersihkeun remot nganggo lawon anu lemes sareng garing. Entong nganggo bahan kimia anu keras atanapi pembersih anu kasar.
7. Cara ngungkulan
- Jauh teu ngabales: Check if the batteries are properly installed and charged. If the LED flashes, replace the batteries.
- rentang ngurangan: This is often an indication of low batteries. Replace them as described in the Maintenance section.
- Masalah pamrograman: Ensure you are following the programming steps precisely for your specific receiver type. Verify that you have access to the receiver's programming buttons.
- gangguan: Strong radio interference from other devices might affect the remote's performance. Try operating the remote from a different location or checking for sources of interference.
8. Tips pamaké
- Always keep a spare set of batteries on hand to avoid interruptions in service.
- Mertimbangkeun purchasing a multi-pack of remotes if you have multiple users or vehicles, as programming multiple remotes at once can be more efficient.
- If you encounter persistent issues, refer to the official user manual for your specific garage door or gate opener receiver, as programming steps can vary.
9. miceun
When disposing of the remote control or its batteries, please adhere to local regulations for electronic waste and battery recycling. Materials should be sorted by type for proper recycling. Instructions are subject to change without notice.
10. Garansi jeung Rojongan
For any product-related inquiries, technical support, or warranty information, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.
