1. Bubuka
Thank you for choosing the AOC AM400/AM500PLUS Series Monitor Stand. This robotic arm computer display lifting cantilever base is designed to enhance your workspace ergonomics and provide flexible monitor positioning. Please read this manual carefully before installation and use to ensure proper setup and safe operation.
2. Warnings Kasalametan jeung precautions
- **VESA Compatibility:** Ensure your monitor has 75x75mm or 100x100mm VESA mounting holes on the back.
- **Desktop Suitability:**
- DO NOT install on fragile desktops such as marble, rock slab, or glass.
- DO NOT install on desktops with beams or baffles that make the clamping area too small.
- DO NOT install on desktops with irregular or slanted edges in the clampwewengkon.
- **Installation Orientation:**
- DO NOT install upside down.
- DO NOT use as a hanging clamp (e.g., clamping to an overhead shelf).
- DO NOT use in reverse orientation.
- **Handling During Installation/Adjustment:**
- When disassembling equipment from the bracket, first adjust the bracket to its highest position to prevent rapid rebound of the bracket, which may cause harm to people or equipment.
- During installation or adjustment, please support the arm by hand and slowly release it after confirming the support force is normal.
- Damage to equipment or assets caused by not operating according to these instructions will not be compensated.
3. Parentah Setup
The AOC monitor stand features a simple three-step installation process, allowing for easy setup by one person.
3.1. Milih hiji Métode Instalasi
The AM400/AM500PLUS series uses an integrated base that supports both clamp and grommet installations. Choose the method suitable for your desktop:
| Modél | Clamp Installation (Desktop Thickness) | Grommet Installation (Hole Diameter & Desktop Thickness) |
|---|---|---|
| AM400/AM500PLUS | 15-50mm | ≥60mm hole diameter |
| AM500PLUS (Enhanced) | 15-90mm | >10mm hole diameter, 15-90mm thickness |
3.2. Lengkah-demi-Lengkah Instalasi
- **Monitor Interface Installation:** Attach the VESA plate to the back of your monitor. Ensure the screws are tightened securely.
- **Bracket Arm Installation:** Connect the monitor arm to the base.
- **Base Installation:** Secure the base to your desktop using either the clamp or grommet method, depending on your chosen option and desktop type.
3.3. Addressing Common Installation Issues
- **Recessed Monitor Back:** If your monitor has a recessed VESA mounting area, use the extended screw assembly included in the package.
- **Long Hand-Tightened Screws:** If the hand-tightened screw is too long, use the provided 4mm washer on the screw before tightening.
4. Parentah Operasi
The AOC monitor stand offers flexible adjustments for optimal viewkanyamanan sarta produktivitas.
4.1. Nyaluyukeun Posisi Monitor
Utilize the four-dimensional control system to position your monitor exactly as needed:
- **Rotation:** Rotate your screen 360° for horizontal or vertical orientation.
- **Height Adjustment:** Adjust the monitor height by up to 250mm for sitting or standing use.
- **Depth Adjustment:** Push or pull the monitor arm to adjust the distance from 87mm to 485mm.
- **Tilt Adjustment:** Tilt the monitor from -15° to 90° to find your preferred viewsudut ing.
4.2. Pangaluyuan Tegangan
The monitor arm features a mechanical spring system for dynamic hovering and single-finger control. If the arm feels too stiff or too loose for your monitor's weight, you can adjust the tension using an Allen key (usually included in the package). Locate the damping arm adjustment point on the arm and turn the screw clockwise to increase tension or counter-clockwise to decrease tension until the monitor holds its position stably.
5. Pangropéa
- **Cleaning:** Wipe the monitor stand with a soft, damp lawon. Hindarkeun ngagunakeun bahan kimia anu kasar atanapi pembersih abrasive anu tiasa ngaruksak finish.
- **Cable Management:** Utilize the integrated flame-retardant cable management slot to keep your desktop tidy and prevent cable damage.
- **Periodic Check:** Periodically check all screws and connections to ensure they are secure. Tighten if necessary.
6. Cara ngungkulan
- **Monitor not holding position:** The tension of the arm may be too low for your monitor's weight. Refer to Section 4.2 for tension adjustment.
- **Arm is too stiff to move:** The tension of the arm may be too high. Refer to Section 4.2 for tension adjustment.
- **Monitor wobbles:** Ensure all mounting screws (VESA plate to monitor, arm to base, base to desk) are securely tightened.
- **Installation issues:** Refer to Section 3.3 for solutions to common installation problems like recessed monitor backs or long screws.
7. Spésifikasi
| Fitur | Katerangan |
|---|---|
| Modél | AM400 / AM500PLUS |
| Ukuran Monitor anu Cocog | 17" - 34" |
| Kapasitas Bearing Beban | 2 - 9 kg |
| Kasaluyuan VESA | 75x75mm, 100x100mm |
| Métode Pamasangan | Snap-on (Clamp atanapi Grommet) |
| adjustment jangkungna | Nepi ka 250mm |
| adjustment jero | 87mm - 485mm |
| Adjustment Dengdekkeun | -15 ° ka 90 ° |
| Rotasi | 360° (Horizontal/Vértikal) |
| Bahan | Precision Aluminum |
| Fitur husus | Mechanical Spring, Stable Head Design, Cable Management |
8. Tips pamaké
- **Ergonomic Posture:** Adjust your monitor to eye level to maintain a healthy viewing posture, reducing strain on your neck and eyes.
- **Optimize Workspace:** Use the flexible adjustments to free up desk space and create a more organized and efficient work area.
- **Cable Management:** Always route cables through the integrated cable management channels to keep your desk tidy and prevent cable damage.
9. Garansi jeung Rojongan
The AOC Monitor Stand AM400/AM500PLUS Series comes with a **Five-Year Warranty**.
For technical support or inquiries, please contact the seller directly:
- Email: hnbydzsw1111@126.com
- WhatsApp: +86 19376855707
- WeChat: Hnhy19376855707
