Yinuogo Multi-Frequency Garage Door Remote Control

1. Bubuka

This manual provides detailed instructions for the Yinuogo YNG800 multi-frequency garage door remote control. This device is designed to clone existing garage door remotes, supporting a wide range of frequencies and both fixed and rolling codes. Please read these instructions carefully before attempting to program or use the remote control.

Catetan penting:

• Your original remote control must be fully functional for successful cloning.
• You must have physical access to your garage door receiver for certain programming steps, especially for rolling code systems.

2. Spésifikasi

The YNG800 remote control features an exquisite appearance design and a durable metal frame. Each button supports the full 280MHz-868MHz frequency range.

Image: Two Yinuogo remote controls, showcasing desain sleek maranéhna.

Image: Two Yinuogo remote controls, emphasizing their 'ALL-IN-1' multi-frequency capability.

Image: Diagram illustrating that each button on the remote supports the 280MHz-868MHz frequency range.

3. Model cocog

The YNG800 remote control is compatible with the following garage door remote series:

• PHOX 2 / PHOX 4
• HANDY 2 / HANDY 4
• TXC4 / TRC4 / TSC4
• PHOENIX 2 / PHOENIX 4

Bantahan:

Your original remote control must be working properly, and its brand/model must be listed above. This remote is not universally compatible with all brands; it supports approximately 98% of market brands. If you are unsure about your original remote's brand or frequency, please do not purchase without confirming.

Image: The Yinuogo YNG800 remote control shown with several compatible original remote controls.

4. Setelan sareng Pemrograman

The YNG800 remote control can duplicate both fixed code and rolling code remotes. The procedure varies slightly depending on the code type.

4.1. Fixed Code Duplicating Procedures

1. While pressing button 1 on the YNG800, press button 2 four (4) times.
2. Release both buttons. The YNG800's LED will now emit a quick flash every 2 seconds.
3. Place your original remote control in front of the new YNG800 remote, at a distance of approximately 4-60 cm.
4. Press and hold the button on your original remote control that you wish to copy. Continue holding until the YNG800's LED changes its flashing frequency (flashing faster than before), confirming successful code copy.
5. While the YNG800's LED is still flashing, press the desired button on the YNG800 where you want to store the copied code. Hold until the LED turns off.
6. Kodeu parantos hasil disalin.

4.2. Rolling Code Duplicating Procedures

1. While pressing button 1 on the YNG800, press button 2 four (4) times.
2. Release both buttons. The YNG800's LED will now emit a quick flash every 2 seconds.
3. Place your original remote control in front of the new YNG800 remote, at a distance of approximately 4-60 cm.
4. Press and hold the button on your original remote control that you wish to copy. Continue holding until the YNG800's LED turns on with a steady light and then emits a double flash every 2 seconds.
5. Transmit the seed code of the original remote control. This is typically done by pressing a rear hide button or buttons 1 and 2 simultaneously on the new YNG800 remote.
6. Now the YNG800's LED will flash quickly. Press the desired button on the YNG800 where you want to store the code just copied. Hold until the LED turns off.
7. Activate the procedure to insert the new remote control on the receiver. This usually involves pressing a learn button on your garage door opener's receiver unit. Refer to your original garage door opener's manual for specific instructions on how to put the receiver into learning mode.

4.3. Auto Matching Code

1. Ensure you are close to the automation (garage door opener).
2. Press and hold the programmed button on the YNG800 for approximately 10 seconds. Release the button when the LED starts to flash.
3. Wait until the LED turns off. The operation is complete, and you can now use your new remote control.

NOTE: The seed code can be emitted as follows:

1. Press buttons 1 and 2 simultaneously for 8 seconds and release them when the LED starts to flash.
2. While the LED is flashing, press the button on the YNG800 with the seed code needed.

Image: Visual guide for fixed code and rolling code duplication.

Image: Diagram indicating the location of button 1 and button 2 for seed code emission.

4.4. Video Demonstrasi

Video: A demonstration of the cloning process for the Yinuogo multi-frequency remote control, showing interaction with a receiver unit.

5. Parentah Operasi

After successful programming, simply press the corresponding button on your YNG800 remote control to activate your garage door or gate. The remote has a range of 30-100 meters in open areas.

Image: The YNG800 remote control with an attached keychain for portability.

Image: The YNG800 remote control conveniently clipped to a car visor.

6. Pangropéa

6.1. Ngagantian batré

The YNG800 remote control uses a CR2032 coin cell battery. When the remote's range decreases significantly or the LED indicator becomes dim, it's time to replace the battery.

1. Buka remot kontrol kalayan ati-atiasing.
2. Leupaskeun batré CR2032 heubeul.
3. Insert a new CR2032 battery, ensuring correct polarity (+ side up).
4. Close the remote control casing aman.

No reprogramming is typically required after battery replacement.

7. Cara ngungkulan

7.1. Remote Not Working After Cloning

• Original Remote Functionality: Ensure your original remote control is working correctly before attempting to clone. The YNG800 cannot clone a non-functional remote.
• Distance During Cloning: Make sure the original remote and the YNG800 are within 4-60 cm during the cloning process.
• Fixed vs. Rolling Code: Verify if your original remote uses a fixed or rolling code. Rolling code remotes require an additional step of programming/activating on the receiver unit after cloning.
• Receiver Access: For rolling code remotes, ensure you have access to the garage door opener's receiver to complete the learning process.
• Button Press Duration: Ensure you press and hold buttons for the specified duration during programming steps.

7.2. Reduced Range

• Tingkat batré: Check the battery. A low CR2032 battery can significantly reduce the remote's operating range.
• Halangan: Ensure there are no major physical obstructions between the remote and the receiver.
• gangguan: Strong radio frequency interference in the area can affect the remote's range.

8. Tips pamaké

• Contact Support for Specific Brands: If you encounter difficulties with a particular brand or model, especially if it's a less common one, contact customer support. Some brands may have unique cloning methods that require specific guidance.
• Keep Original Manuals: Always retain the instruction manuals for your original garage door remote and opener, as they may contain crucial information for receiver programming.
• Uji sacara saksama: After programming, test the new remote control multiple times from various distances and angles to ensure reliable operation.

9. Garansi jeung Rojongan

9.1. Garansi

All Yinuogo products come with a 1-year warranty from the date of purchase.

9.2. Rojongan Palanggan

If you have any questions, require assistance with programming, or need further information, please contact Yinuogo customer support. You can reach us via email at: evan.yinuogo@foxmail.com.

We are committed to providing prompt assistance and will respond to inquiries within 24 hours.

Additionally, a user manual in PDF format is available for download. You can find it by searching for "Item guides & documents" on the product page or by contacting support for a direct link: Manual pamaké (PDF)