Bubuka
The Gaqqee W3103 Digital Display Thermostat is a high-precision temperature control system designed for a wide range of applications, including heating and cooling scenarios. This manual provides detailed instructions for its installation, operation, and maintenance to ensure optimal performance and longevity of the device.
spésifikasi
The following table details the technical specifications of the W3103 Digital Display Thermostat:
| Parameter | Nilai |
|---|---|
| Modél produk | W3103 |
| Ngaran produk | Suhu Controller |
| Masukan Voltage | DC12V / DC24V / AC220V (Optional) |
| Jenis Fungsi | Ngadalikeun Suhu |
| Tipe Kaluaran | Langsung Voltage Kaluaran |
| Tipe Kontrol | Kontrol Bit |
| Input pangukuran | NTC 10K / B3435, L = 1 meter |
| Rentang Ukur Suhu | -50 nepi ka 110 ℃ |
| Daya Kaluaran | 300W (for 12V), 600W (for 24V), 5000W (for 220V). Maximum current: 30A. |
| Akurasi Pangukuran Suhu | ± 0.2 ℃ |
| Rentang Kontrol Suhu | -19 nepi ka 99 ℃ |
| Kontrol Akurasi | 1 ℃ |
| Diménsi Penampilan | 96 x 70 x 46 mm |
| Batré Kaasup | No |
| Kimia anu prihatin tinggi | Euweuh |
| Asalna | Daratan Cina |
Setup sareng Instalasi
Before installation, ensure the power supply is disconnected to prevent electric shock. The W3103 thermostat is designed for wall-hanging installation.
1. Pamasangan
Secure the thermostat to a wall or suitable surface using screws through the designated mounting holes on the back of the device.
2. Kabel
Connect the power supply and load according to the appropriate wiring diagram for your chosen voltage (DC12V/24V or AC220V). Ensure all connections are secure and correctly polarized.
3. Temperature Sensor Connection
Connect the provided NTC 10K/B3435 temperature sensor (L=1 meter) to the sensor input terminals on the device. Ensure the sensor is placed in the environment where temperature measurement is required.
Parentah Operasi
The W3103 thermostat offers four main operational modes: Temperature Control, Intermittent Operation, Scheduled Shutdown, and Scheduled Startup.
1. Temperature Control Mode (F0)
After power is turned on, the number displayed in the middle of the screen is the temperature control mode (F0). If it is not a number, you can short press the middle function switch key (SET button) to cycle to F0.
- Setting Start Temperature: Press the left Up or Down key. The start temperature display will flash. Use the Up and Down keys to adjust the desired start temperature. The setting will automatically save without further operation.
- Setting Stop Temperature: Press the right Up or Down key. The stop temperature display will flash. Use the Up and Down keys to adjust the desired stop temperature. The setting will automatically save without further operation.
2. Intermittent Mode (F1)
To enter Intermittent Mode, short press the SET button until "F1" is displayed in the middle of the screen.
- Setting Start Time (ON duration): Press the left Up or Down key. The start time display unit (minutes) will flash. Use the Up and Down keys to adjust the desired ON duration. The setting will automatically save.
- Setting Stop Time (OFF duration): Press the right Up or Down key. The stop time display unit (minutes) will flash. Use the Up and Down keys to adjust the desired OFF duration. The setting will automatically save.
3. Scheduled Shutdown (F2) and Scheduled Startup (F3)
To access these modes, short press the SET button to cycle to F2 (scheduled shutdown) or F3 (scheduled startup).
- Setélan waktos: In F2 or F3 mode, use the Up and Down keys associated with the "Start setting" or "Stop setting" to adjust the desired time in minutes. The setting will automatically save.
4. Temperature Correction Function
This function allows you to calibrate the temperature reading if there is a discrepancy with a known accurate thermometer.
- Entering Correction Setting: Long press the SET button for more than 3 seconds. The display will show the temperature correction difference and the code "BCAJ".
- Adjusting Correction Value: Use the right Up and Down keys to set the desired temperature difference value. This value will be added to the measured temperature. The setting will automatically save.
Pangropéa
To ensure the longevity and accurate operation of your W3103 thermostat, follow these maintenance guidelines:
- beberesih: Regularly wipe the device with a soft, dry cloth. Do not use abrasive cleaners or solvents, as they may damage the casing atawa tampilan.
- Perawatan sénsor: Keep the temperature sensor clean and free from debris. Avoid bending or damaging the sensor cable.
- Kaayaan Lingkungan: Ensure the thermostat is operated within its specified environmental conditions (temperature, humidity) to prevent malfunction.
- Pegatkeun daya: Always disconnect the power supply before performing any cleaning or maintenance tasks.
Pamérésan masalah
If you encounter issues with your W3103 thermostat, refer to the following common troubleshooting steps:
- Henteu aya tampilan/kakuatan:
- Check the power supply connections to ensure they are secure and the correct voltage (DC12V/24V/AC220V) is being supplied.
- Pariksa yén sumber daya aktip.
- Maca Suhu anu teu akurat:
- Pastikeun sensor suhu disambungkeun kalayan leres sareng henteu ruksak.
- Check if the sensor is placed correctly in the environment to be measured.
- Use the Temperature Correction Function (refer to Operating Instructions) to calibrate the reading if necessary.
- Output Not Activating/Deactivating:
- Verify that the start and stop temperature/time settings are correctly configured for the desired operation.
- Check the wiring to the load to ensure it is correctly connected and the load itself is functional.
- Ensure the device is in the correct operating mode (Temperature Control, Intermittent, Scheduled).
- Tombol teu responsif:
- Try power cycling the device (disconnect and reconnect power).
- Pastikeun euweuh lebu anu ngahalangan tombol.
Lamun masalah persists sanggeus nyobian léngkah ieu, mangga ngahubungan rojongan customer.
Tip pamaké
- Setup Awal: Always double-check your wiring against the provided diagram, especially for DC vs. AC versions, to prevent damage.
- Panempatan sénsor: For best accuracy, place the temperature sensor away from direct heat sources, drafts, or extreme cold spots that do not represent the average temperature of the area you wish to control.
- Kalibrasi: If precise temperature control is critical, use a known accurate thermometer to verify the W3103's reading and apply temperature correction if needed.
- Ngalihkeun Mode: Remember to short press the SET button to cycle through the different operating modes (F0, F1, F2, F3) to access the desired functionality.
Garansi sareng Rojongan
Kanggo inpormasi garansi, dukungan téknis, atanapi patarosan jasa, mangga ngahubungi penjual atanapi produsén langsung. Simpen resi pameseran anjeun salaku bukti pameseran.
